User manual NVIDIA NFORCE 410 MCP REV 1.0

[. . . ] USER'S MANUAL Of GeForce6100 GPU & nForce 410 MCP M/B For Socket AM2 64-bit Dual Core AMD Processor NO. G03-M2GT3-FR111 Rev:1. 0 Release date: June 2006 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer. Environmental Protection Announcement Do not dispose this electronic device into the trash while discarding. To minimize pollution and ensure environment protection of mother earth, please recycle. ii TABLE OF CONTENT USER'S NOTICE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii MANUAL REVISION INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii COOLING SOLUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii CHAPTER 1 INTRODUCTION OF GEFORCE 6100 GPU MOTHERBOARDS 1-1 1-2 1-3 1-4 2-1 2-2 2-3 2-4 2-5 FEATURE OF MOTHERBOARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1-1. 1 SPECIAL FEATURES OF MOTHERBOARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press (up, down, left, right) to choose, in the main menu, the option you want to confirm or to modify. Press <F10> when you have completed the setup of BIOS parameters to save these parameters and to exit the BIOS Setup menu. Press Page Up/Page Down or +/­ keys when you want to modify the BIOS parameters for the active option. 3-1 Entering Setup Power on the computer and by pressing <Del> immediately allows you to enter Setup. If the message disappears before your respond and you still wish to enter Setup, restart the system to try again by turning it OFF then ON or pressing the "RESET" button on the system case. You may also restart by simultaneously pressing <Ctrl>, <Alt> and <Delete> keys. If you do not press the keys at the correct time and the system does not boot, an error message will be displayed and you will again be asked to Press <F1> to continue, <Ctrl-Alt-Esc> or <Del> to enter Setup 3-2 Getting Help Main Menu The on-line description of the highlighted setup function is displayed at the bottom of the screen. Status Page Setup Menu/Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window, press <Esc>. 21 3-3 The Main Menu Once you enter Award® BIOS CMOS Setup Utility, the Main Menu (Figure 3-1) will appear on the screen. The Main Menu allows you to select from fourteen setup functions and two exit choices. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu. Phoenix ­ AwardBIOS CMOS Setup Utility Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup Miscellaneous Control PC Health Status Esc : Quit F9 : Menu in BIOS F10 : Save & Exit Setup Thermal Throttling Options Power User Overclock Settings Password Settings Load Optimized Defaults Load Standard Defaults Save & Exit Setup Exit Without Saving : Select Item Figure 3-1 Standard CMOS Features Use this Menu for basic system configurations. Advanced BIOS Features Use this menu to set the Advanced Features available on your system. Advanced Chipset Features Use this menu to change the values in the chipset registers and optimize your system's performance. Integrated Peripherals Use this menu to specify your settings for integrated peripherals. Power Management Setup Use this menu to specify your settings for power management. Miscellaneous Control Use this menu to specify your settings for Miscellaneous control. PC Health Status This entry shows your PC health status. Thermal Throttling Options The selection is set for activating the active CPU Thermal Protection by flexible CPU loading adjustment in the arrange of temperature you define. 22 Power User Overclock Settings Use this menu to specify your settings (frequency, Voltage) for overclocking demand Password Settings This entry for setting Supervisor password and User password Load Optimized Defaults Use this menu to load the BIOS default values these are setting for optimal performances system operations for performance use. Load Standard Defaults Use this menu to load the BIOS default values for the stable performance system operation that are factory settings for normal use. Save & Exit Setup Save CMOS value changes to CMOS and exit setup. Exit Without Saving Abandon all CMOS value changes and exit setup. 3-4 Standard CMOS Features The items in Standard CMOS Setup Menu are divided into several categories. Each category includes no, one or more than one setup items. Use the arrow keys to highlight the item and then use the <PgUp> or <PgDn> keys to select the value you want in each item. Phoenix ­ AwardBIOS CMOS Setup Utility Standard CMOS Features Time (hh:mm:ss) > > > > IDE IDE IDE IDE Channel Channel Channel Channel 0 0 1 1 Master Slave Master Slave 16 : 48 : 35 None None None None 1. 44M, 3. 5 in. All, But Keyboard 640K 522240K 523264K Item Help Menu Level > Change the day, month, year and century Drive A Halt On Base Memory Extended Memory Total Memory Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F5:Previous Values F6:Optimized Defaults F1:General Help F7:Standard Defaults Date The date format is <day><month><date><year>. [. . . ] Installation of Windows XP/ Windows 2000 For installation of Windows XP or Windows 2000, please insert Windows XP or Windows 2000 CD into the CD-ROM drive. Then remove the floppy diskette, and boot the system. At the very beginning, you will see the message at the bottom of screen, "Press F6 if you need to install a third party SCSI or RAID driver. . . . " At this moment, please press <F6> key and follow the instructions of Windows XP or 46 Windows 2000 for the proper installation. Execute Start programs NVIDIA corporation RAID manager , you can view RAID function status or rebuild RAID function from Windows OS 4-9 Pro Magic Plus Function Introduction What's Pro Magic Plus? Tired with reinstall OS each time when it doesn't work? [. . . ]