User manual OKI B6200N SETUP GUIDE

[. . . ] PREFACE Every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date. The manufacturer assumes no responsibility for the results of errors beyond its control. The manufacturer also cannot guarantee that changes in software and equipment made by other manufacturers and referred to in this guide will not affect the applicability of the information in it. Mention of software products manufactured by other companies does not necessarily constitute endorsement by the manufacturer. [. . . ] By using the arrow buttons as indicated above, you can navigate through the menu system to make any required settings. For example, to set the paper type in Tray 1 to accommodate recycled paper, navigate as follows: Admin Menu, Printer Settings, Paper Type, Tray 1, Recycled then press the <FEED/SELECT> button to record the setting and the <MENU> button to close the menu screen. 44 > INSTALLATION AND RELOCATION PROCEDURE SELECTING THE CONTROL PANEL LANGUAGE English is the default language for all error and status messages; however, these messages are also available in many languages. Use the following procedure to change the display language. NOTE Refer to the section "The Control Panel and Menu system" on page 43 for a brief overview of the control panel and its menus and sub-menus. Press the <MENU> button to display the Menu screen. Press the < > or < > button until [Display Language] is displayed, then press the < > button. Press the < > or < > button until the required language is displayed, then press the <FEED/SELECT> button. Press the <MENU> button to complete the language setting. INSTALLATION AND RELOCATION PROCEDURE > 45 PRINTING A CONFIGURATION SUMMARY To check whether the printer is correctly installed, use the control panel to print the [System Settings List]. NOTE If you have made a mistake when operating the control panel, press the <MENU> button to restart. For details on how to operate the control panel, refer to "The Control Panel and Menu system" on page 43. Press the <MENU> button to display the Menu screen. Press the < > or < > button until [Report/List] is displayed, then press the < > button. Press the < > or < > button until [System Settings] is displayed, then press the < > button. The [System Settings List] will be printed. Press the <MENU> button when printing has completed. NOTE > The layout of the [System Settings List] may differ depending on the configuration and settings of the printer. > For B6300, [Rear Output Tray] is displayed in the column for Output Device even when the rear tray is not installed. > Reports/lists cannot be output to the face up (rear) tray. When the face up (rear) tray is installed, lower the face up (rear) tray output lever. 46 > INSTALLATION AND RELOCATION PROCEDURE SETTING PRINTER CONFIGURATIONS VIA A WEB PAGE If you are working in a TCP/IP-enabled environment, you can use a web browser to display the printer or job printing status and to change the settings. Among the printer settings that are made on the control panel, settings for the system and network ports can be configured under [Printer], [Network] and Maintenance] on the web page. NOTE > The web page facility is only available when the printer is connected to the network. > Refer to the Reference Guide when the web page does not appear after carrying out the steps 1 and 2 below. > You can also use Telnet to set the printer configuration. For details on the settings, refer to the NIC Configuration Guide. Boot your computer, and start the web browser. Enter the printer's IP address or URL in the address input column on the web browser and press the <Enter> key. Using Online Help For details regarding the items that can be set in each screen, click the [Help] button to display the Online Help. INSTALLATION AND RELOCATION PROCEDURE > 47 INSTALLING THE PRINTER DRIVER To print from the computer, install the printer driver and other required software. [. . . ] On-Site Repair does not include the replacement or repair of product consumables or supplies. Oki Data will, for a period of one (1) year from the date of original purchase, repair or replace (at Oki Data's option) on-site at the original purchaser's facility and without charge, any defective component(s) of the printer, provided that the warranty service is performed by an Oki Data authorized service provider. Oki Data reserves the right to use new and/or refurbished parts in the warranty repair process. As a condition of this Limited Warranty, requests for On-Site Repair must include the name and phone number of a fully competent and responsible adult with the authority to consent to the entry of the servicing technician to the premises where the printer is located, and who will remain with the servicing technician while the service work is performed. [. . . ]