User manual OKI C9200 NETWORK CARD

[. . . ] OkiLAN 6020e® Pocket Print Server User's Guide High Performance 10/100 Base-T Ethernet Network Print Server Copyright and Trademark Information Every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date. Oki Data assumes no responsibility for the results of errors beyond its control. Oki Data also cannot guarantee that changes in products made by other manufacturers and referred to in this handbook will not affect the applicability of the information in it. This handbook is subject to change without notification. [. . . ] If you disable a protocol, the OkiLAN 6020e will no longer communicate using that protocol. SNMP Trap Configuration The SNMP Trap option allows configuration of traps. Traps are unsolicited information concerning the OkiLAN 6020e. Traps can be sent to an SNMP manager or be broadcast to all hosts on the local segment. To configure SNMP traps, select the SNMP Traps tab. Note: SNMP options need to be configured only if you are managing an OkiLAN 6020e or getting system information using SNMP. Protocol Select the protocol for which you wish to configure trap information. IV - 32 OKI OkiLAN 6020e User's Guide Section 4 - Chapter 4 - OkiNet for TCP/IP Trap Destination · TCP/IP Protocol - Enter the IP address to which traps will be sent. The IP address must follow the format XXX. XXX. XXX. XXX, where each XXX is a number from 0 to 255. To broadcast traps to all hosts on the local subnet, enter 255. 255. 255. 255. · NetWare Protocol - Enter the network number and hardware address, respectively, to which traps will be sent. To broadcast traps to all addresses on all networks, enter FFFFFFFF (8 characters) in the first field and FFFFFFFFFFFF (12 characters) in the second field. To broadcast traps to all addresses on a specific network, enter the network number in the first field and then FFFFFFFFFFFF (12 characters) in the second field. Ports to Trap Select the output ports on which you wish traps to be active. Printer Traps Select the printer traps to be activated. The following printer error conditions may cause a printer trap to occur: · On-line · Off-line · No Printer Attached · Paper Out · Paper Jam · Door Open · Toner Low · Printer Error The toner low, door open and paper jam traps require that your printer be set to automatic emulation switching (the default) or PCL emulation. OKI OkiLAN 6020e User's Guide IV - 33 TCP/IP Section 4 - Chapter 4 - OkiNet for TCP/IP Saving the Configuration Once all settings have been defined, select OK. The settings will be saved and you will be returned to the main OkiNet for TCP/IP screen. Displaying OkiLAN 6020e Diagnostic Information To view OkiLAN 6020e diagnostic information, double click on Diagnostics from the Print Server pull-down menu on the main OkiNet TCP/IP screen. Diagnostic information is available on the following topics: · Printer · Print Server · Protocols · Network · Statistics · Technical Support · System Printing a Configuration Sheet The configuration sheet provides current network, print server and printer information. To print a configuration sheet, select the OkiLAN 6020e from the list of available print servers. Select Print Configuration Sheet from the Print Server menu bar. Resetting the OkiLAN 6020e To reset the OkiLAN 6020e, select the OkiLAN 6020e from the list of available print servers. From the Print Server menu bar, select Reset. CAUTION: Make sure there are no print jobs active when you reset the OkiLAN 6020e. If you attempt a reset while a job is printing, the job may not print successfully. IV - 34 OKI OkiLAN 6020e User's Guide Section 4 - Chapter 4 - OkiNet for TCP/IP Restoring Factory Default Settings To restore the OkiLAN 6020e to factory default settings, select the OkiLAN 6020e from the list of available print servers. From the Print Server menu bar, select Reset. From the Reset Print Server screen, choose one or more of the following options: Output Ports Restores settings related to output ports such as port name and output type. TCP/IP Restores settings specific to the TCP/IP protocol configuration such as the IP address and subnet mask. NetWare Restores settings specific to the NetWare protocol configuration such as the mode and default file server. Banyan VINES Restores settings specific to the VINES protocol configuration such as user name and print service names (may apply to other OkiLAN print server models). EtherTalk Restores settings specific to the EtherTalk protocol configuration such as the name and zone. Once you have chosen the desired options, select Restore. To completely restore the print server to factory default settings, select all items in the list. CAUTION: Make sure there are no active print jobs when you select Restore Factory Defaults. [. . . ] Network Property Page The Network Property Page is reached from the Printer Properties menu. This screen allows you to configure the network protocol, network frames, and SNMP traps events and destination addresses. Information includes: · Protocols - TCP/IP - NetWare - AppleTalk - NetBEUI - Lan Manager - Banyan VINES · Frame Types · SNMP Traps Novell Configuration Note: This screen is only available when Novell's Client for Windows 95/98, NT or 2000 is installed. The Novell Configuration screen is reached from the Printer Properties menu. [. . . ]