User manual OKI OL 830 ACCESSORY INSTRUCTION GUIDE

[. . . ] 802. 11b Print Server User's Guide Part Number 40148-100 Revision 1. 0 Copyright Notice All rights reserved. No part of this publication may be reproduced, stored, in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of TROY Group, Inc. The information contained herein is designed only for use with this TROY product. TROY is not responsible for any use of this information as applied to other products. [. . . ] You should now be able to print using the lp -d command with the printer name. Notes: The configuration for HP Distributed Print Services and for earlier versions of HP/UX is slightly different. The print server can also be configured as a JetDirect card using HP/UX. To do this, you will need the HP UNIX Host Printing Software (part of HP's JetAdmin for UNIX). IBM AIX Configuration To configure a print server on IBM AIX 4. x, use the SMIT program as follows: 1. Enter smit and select Devices Select Printer/plotter Select Manage remote printer subsystem Select Client services Select Remote printer queues Select Add a remote queue Enter the following remote queue settings: · Name of queue to add (user selectable) · Activate the queue (Yes) · Destination host (EtherWind IP address; or if you have configured the /etc/hosts file, use the name of the print server that you specified in that file) · Name of queue on remote printer (BINARY_P1 for binary files or TEXT_P1 for text files) · Name of device to add (user selectable; for example lp0) 8. You should now be able to print using the normal lp -d command. Notes: The configuration for earlier versions of AIX is slightly different. Refer to the Administrator's Manual on the CD-ROM for details. The print server can also be configured as a JetDirect card using AIX. To do this, refer to your AIX documentation. Configuration on Other Systems The EtherWind can be used with any computer system that supports either the lpr/lpd protocol or the HP JetDirect card (the EtherWind parallel port is port 9100 while the serial port is port 9101). Refer to your system's documentation for information on configuring lpr/lpd or JetDirect print queues. 7-4 8 DEC LAT Network Configuration Note: Only TROY EtherWind-N models include DEC LAT support. The EtherWind wireless print server acts as a node on an Ethernet network that offers printing services to other devices. The print server comes preconfigured to run on a LAT network and does not require any additional setup. Each print server has a default node name of XCD_xxxxxx (where "xxxxxx" are the last six digits of the Ethernet address of the unit). The port name is P1 for the EIO, MIO, or first parallel port; S1 for the first serial port, P2 for the second parallel port, and S2 for the second serial port. VMS LAT Host Configuration Use the VMS editor to create a text file with the necessary configuration commands to create a LAT application port and then a VMS print queue. For example: $MCR LATCP CREATE PORT LTAxx:/APPLICATION SET PORT LTAxx:/NODE=nodename/PORT=port SHOW PORT LTAxx: EXIT $SET TERM LTAxx:/PASSTHRU/PASSALL/TAB/NOBROADCAST/PERM $SET DEVICE/SPOOL LTAxx: $INIT/QUEUE/START/ON=LTAxx:/PROC=LATSYM queuename Note: LTAxx is the available LAT port to be used nodename is the node name of the print server port is the port, e. g. P1, S1, P2, S2 & LN queuename is any unique name for the print queue. 8-1 Execute the command file. At the VMS "$" prompt type: @filename where filename is the name of the text file created in step 1. Note: The @filename command can be included in the system startup file so that the procedure is executed automatically when the system is booted. Use the VMS PRINT command with the name of the queue and the file you wish to print as shown below: PRINT/QUEUE=queuename filename Note: queuename is the name of the print queue created in step1. filename is the name of the file to be printed. For graphics or PostScript jobs, the form MUST be defined for NOTRUNCATE and NOWRAP to prevent printer errors. DEFINE/FORM DEFAULT/NOTRUNCATE/NOWRAP 8-2 9 Banyan VINES Network Configuration Note: Only TROY EtherWind-N models include Banyan VINES support. EtherWind wireless print servers support the Banyan VINES IP protocol to allow printers to be shared on a Banyan VINES network. Users on client PC's send their jobs to any VINES file server running the Banyan PCPrint software, which in turn spools jobs to the print server. Printing is transparent to user applications, and the print server can be managed using standard VINES utilities such as MANAGE, MUSER, MSERVICE and Operator Console. File Server User Configuration 1. From any VINES workstation log in as supervisor and run the MANAGE program. [. . . ] If this equipment has more than one interface connector, do not leave cables connected to unused interfaces. Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. For European Users This product is in conformity with the protection requirements of EU Council Directive 89/336/EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility. TROY Group cannot be responsible for any failure to satisfy the protection requirements resulting from a nonrecommended modification of the product. This product has been tested and found to comply with the limits for Class B Information Technology Equipment according to CISPR 22/European Standard EN55022. [. . . ]