User manual OLITEC PCI 802-11 G QUICK INSTALLATION GUIDE

[. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures: reorient the receiving antenna; relocate the computer with respect to the receiver; move the computer away from the receiver; plug the computer into a different outlet so that the computer and receiver are on different branch circuits. If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet prepared by the Federal Communications Commission helpful: "How to identify and Resolve Radio/TV Interference Problems. " This booklet is available from the U. S. [. . . ] When you have finished editing parameters and are ready to resume normal operation, return the VARIATION knob to its prior setting, or you will load a new program based on its position when you exit System Mode. (The Tap LED will light when VARIATION matches its prior setting. ) To exit System Mode, Press Bypass. If you have changed any System parameters, the Store LED will flash rapidly. 13 Press and hold Bypass for 2 seconds. . . . . . The Bypass and Store LEDs will blink slowly to indicate you are in System mode. System Mode Parameters Variation Setting 1 2 3 4 5 6 7 8 Parameter Bypass Patching Program Load Digital Output MIDI OUT/THRU MIDI Pgm Change MIDI Clock Receive Tempo State when Edit LED is: On Off Mute Disabled Mute Dry Out* Disabled Disabled Program* Bypass* Enabled* Bypass* Wet* Thru Enabled* Enabled* Global Turn VARIATION to select a parameter. Press Store to toggle the parameter state (or to execute a MIDI dump). MIDI Dumps (Press Store to Transmit) 14 Dump User Programs 15 Dump Current Program 16 Dump System and Learned patches Turn VARIATION until the Tap LED goes on to find the last loaded program. . . then press Bypass to exit System Mode. * Factory Default System parameters MIDI Dumps 14 System Mode Parameters 1 Bypass Mute/Bypass This parameter sets the Bypass button (or the footswitch, or MIDI controller assigned to Bypass) to mute the inputs, or to bypass the processed audio (passing only dry audio to the outputs). 2 Patching Disable/Enable This parameter allows you to temporarily suspend (Disable) and restore (Enable) any Learned patches. 3 Program Load Mute/Bypass This parameter determines whether the PCI 802-11 G will engage wet mute or simply bypass processed audio during program load. 4 Digital Output Dry/Wet For certain recording and monitoring applications, this parameter allows you to choose to pass only dry audio, or to resume output of the full, processed signal. 5 MIDI OUT/THRU Out/Thru Sets the rear panel MIDI OUT/THRU jack for either MIDI OUT or MIDI THRU functionality. 6 MIDI Pgm Change Disable/Enable The setting of this parameter determines whether or not the PCI 802-11 G will recognize MIDI Program Change messages for loading programs. 7 MIDI Clock Receive Disable/Enable The setting of this parameter determines whether or not the PCI 802-11 G will recognize MIDI Clock messages. 8 Tempo Program/Global Determines whether the current tempo of the PCI 802-11 G will be applied to all programs (Global), or whether program-specific tempos are restored on each program load. As the tremolo rates of several variations are set with Tap, it's easy to match the tempo of the music. Other variations let you set left and right channel waveforms out-ofphase, resulting in a panning motion. All of the variations of this program (1-8) should be used with Mix set to fully Wet. By adding more dry to the wet/dry mix, Mix effectively sets the depth of the Tremolo. Tremolo is a rhythmic change in loudness, commonly employed as an expressive technique by vocalists and wind instrument players. It is also one of the oldest electronic effects -- frequently used with electric guitar, electric piano and, sometimes, vocals. Different tremolo effects are largely determined by the rate and waveform shape of the loudness change (fast or slow, smooth or sharp). If the effect is used in a stereo mix, the left and right can be synchronized in a variety of ways to produce dramatic side-to-side motion. 24 As tremolo is essentially a rhythmic effect, care should be taken to make the rate work with the tempo of the music. Rotary VARIATIONs 9 10 11 12 13 14 15 16 Rotary Rotary Rotary Slow Rotary Varispeed Rotary Tap Rotary Tap Rotary Tap Rotary Adjust Slow/Fast Slow/Fast, Width Slow/Fast, Balance ± Resonance Speed Balance Width ± Resonance Tap ­ ­ ­ ­ ­ Rate (Quarter-Note) Rate (Quarter-Note) Rate (Quarter-Note) Rotary The PCI 802-11 G rotary effect is a detailed simulation of a Leslie-style cabinet. The input signal is split into high and low frequency bands. The rotation effect is created by a synchronized combination of pitch shifting, tremolo and panning. Like the physical model, the high (horn) and low (drum) frequencies are "spun" in opposite directions. Horn and drum speeds are independent, and are designed with acceleration and deceleration characteristics to simulate the inertia of the original mechanical elements. [. . . ] To assign a Program Change message to Bypass or Tap: 1. Simultaneously press Store and Tap to enter Learn Mode. (The Store LED flashes slowly and the Tap LED lights steadily to indicate Learn Mode is active. ) 2. Press the front panel button you want to control (Bypass or Tap). 5. [. . . ]