User manual OLIVETTI D-COLOR P20W-P26W-P26

[. . . ] Digital Color Printer Olivetti d-Color P26 User Guide PUBLICATION ISSUED BY: Olivetti S. p. A. Gruppo Telecom Italia Via Jervis, 77 - 10015 Ivrea (ITALY) www. olivetti. com Copyright © 2006, Olivetti All rights reserved September 2006 The mark affixed to the product certifies that the product satisfies the basic quality requirements. The manufacturer reserves the right to carry out modifications to the product described in this manual at any time and without any notice. ENERGY STAR is a U. S. registered mark. The ENERGY STAR program is an energy reduction plan introduced by theUnited States Environmental Protection Agency in response to environmental issues and for the purpose of advancing the development and utilization of more energy efficient office equipment. Your attention is drawn to the following actions which could compromise the conformity attested to above, as well as the characteristics of the product: · incorrect electrical power supply; · incorrect installation, incorrect or improper use or use not in compliance with the warnings provided in the User's Manual supplied with the product; · replacement of original components or accessories with others of a type not approved by the manufacturer, or performed by unauthorised personnel. All rights reserved. No part of this material may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording or by any information storage and retrieval system, without permission in writing from the Publisher. PREFACE Every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date. [. . . ] Offset relative to [perpendicular] direction adds to your left margin. Offset relative to [parallel] direction adds to your top margin (normal feed) or bottom margin (flipped feed). Click [OK] to close the PostScript Custom Page Size Definition window. Click [OK] to close the Advanced Options window. Colour matching> 87 7. In the driver's window, choose the [Multipurpose Tray] as the [Paper Source]. WINDOWS PCL 1. In the driver's [Setup] tab, select any previously saved settings you wish to use. 2. 5. Click the [Paper Feed Options] button. In the Paper Feed Options window, click [Custom Size]. If you have previously saved any special custom sizes they will be listed in the Custom Size window. To use a previously saved custom size, click its name in the list. To create a new custom size: (a) (b) Enter its dimensions in the [Width] and [Length] boxes. Enter a name for the new size in the [Name] box, and click [Add] to save it in the list. Colour matching> 88 6. 7. Click [OK] to accept your chosen size and close the Custom Size window. If this is the size of your document but you want to scale it to fit a standard size of paper, click [Resize document to fit printer page] in the Paper Feed Options window, and choose the printer's actual paper size from the [Conversion] drop-down list. MAC OS X 1. In your application program, choose [File] [Page Setup]. 1 2 3 4 2. Click the [New] button (2) to define a new paper size and enter a name for the paper size. Enter the [Width] and [Height] (3) of your paper. Specify paper [margins] (4) as required. Click [OK] to save the new paper size. Colour matching> 89 DUPLEX (DOUBLE-SIDED) PRINTING If your printer has a duplex unit installed you can print on both sides of the paper, to save paper, weight, bulk and cost. > Only paper can be used for duplex printing, not transparencies or other media. > Use paper stock of 75­120 g/m². If you experience excessive curling with 75­90 g/m² paper, use 105 g/m². > Use standard sized paper stock only, e. g. [. . . ] Repeat this removal procedure for each of the remaining image drum units. Look into the printer to check whether any sheets of paper are visible on any part of the belt unit. 3 4 2 1 · To remove a sheet with its leading edge at the front of the belt (1), carefully lift the sheet from the belt and pull it forwards into the internal drum cavity and withdraw the sheet. CAUTION! Do not use any sharp or abrasive objects to separate sheets from the belt. This may damage the belt surface. Clearing paper jams> 163 · To remove a sheet from the central area of the belt (2), carefully separate the sheet from the belt surface and withdraw the sheet. 3 4 2 1 · To remove a sheet just entering the fuser (3), separate the trailing edge of the sheet from the belt, push the fuser pressure release lever (4) towards the front and down to release the fuser's grip on the sheet, and withdraw the sheet through the drum cavity area. Then allow the pressure release lever to rise again. NOTE: If the sheet is well advanced into the fuser (only a short length is still visible), do not attempt to pull it back. [. . . ]