User manual OLIVETTI D-COLOR MF35 SUPPLEMENTO

[. . . ] Gruppo Telecom Italia Via Jervis, 77 - 10015 Ivrea (ITALY) www. olivetti. com Copyright © 2006, Olivetti All rights reserved The mark affixed to the product certifies that the product satisfies the basic quality requirements. The manufacturer reserves the right to carry out modifications to the product described in this manual at any time and without any notice. ENERGY STAR is a U. S. registered mark. The ENERGY STAR program is an energy reduction plan introduced by theUnited States Environmental Protection Agency in response to environmental issues and for the purpose of advancing the development and utilization of more energy efficient office equipment. Your attention is drawn to the following actions which could compromise the conformity attested to above, as well as the characteristics of the product: · incorrect electrical power supply; · incorrect installation, incorrect or improper use or use not in compliance with the warnings provided in the User's Manual supplied with the product; · replacement of original components or accessories with others of a type not approved by the manufacturer, or performed by unauthorised personnel. This manual is also available in color PDF format on the CD-ROM provided. All rights reserved. No part of this material may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording or by any information storage and retrieval system, without permission in writing from the Publisher. Contents 1 Introduction Energy Star®. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 What is an ENERGY STAR® product? [. . . ] Was the original not pressed close enough against the original glass? The printed output is blurry. Is the paper damp? Was the original not pressed close enough against the original glass? d-Color MF35 (Phase3) 6-59 6 Symptom There are dark specks or spots throughout the printed output. There are streaks in the printed output. Possible cause Is the original glass dirty?Was the original printed on highly translucent material, such as diazo photosensitive paper or OHP?Is a double-sided original being copied?Remedy Troubleshooting Wipe the glass with a soft, dry cloth. 11-3. ) Clean the left partition glass with the left partition glass cleaner. 11-4. ) Clean the original cover pad with a soft cloth dampened with a mild detergent. 11-5. ) Place a blank sheet of paper on top of the original. 4-11. ) If a thin double-sided original is being copied, the information on the back side may be reproduced in the copy. Touch [Light] on the Background Removal screen to select a lighter background density. 4-74. ) Use the charger-cleaning tool to clean the electrostatic charger. 11-6. ) Correctly position the original against the original scales. 4-11. ) Load the original into the ADF, and slide the lateral guides to fit the size of the original. 4-9. ) If the original cannot be fed correctly through the ADF, make copies by positioning the original on the original glass. 4-11. ) Clean the left partition glass with the left partition glass cleaner. 11-4. ) Slide the lateral guides against the edges of the original. Remove the paper from the paper tray, turn it over, and then load it again. Replace the paper with paper that is not damp. Is the electrostatic charger wire dirty?The image is not aligned properly on the paper. Is the original incorrectly positioned? Is the original incorrectly positioned in the ADF? Is the left partition glass dirty (while using the ADF)?Are the lateral guides incorrectly positioned against the edges of the original? [. . . ] 14-8 d-Color MF35 (Phase3) Appendix 14 Minimal Select this setting to produce a copy with the original image slightly reduced. Mirror Image Set this function to produce a copy in the mirror image of the original. Mixed Original Select this setting to detect the size of each original page and print a copy on paper of the appropriate size when an original with different page sizes is loaded together into the ADF. N Neg-/Pos. Reverse Set this function to copy the original with the light- and dark-colored areas or the colors (gradations) of the image inversed. O Offset Select this setting to separate copies that are fed out. [. . . ]