User manual OLIVETTI D-COPIA 150D

[. . . ] Gruppo Telecom Italia Via Jervis, 77 - 10015 Ivrea (ITALY) www. olivetti. com Copyright © 2006, Olivetti All rights reserved The mark affixed to the product certifies that the product satisfies the basic quality requirements. The manufacturer reserves the right to carry out modifications to the product described in this manual at any time and without any notice. ENERGY STAR is a U. S. registered mark. The ENERGY STAR program is an energy reduction plan introduced by theUnited States Environmental Protection Agency in response to environmental issues and for the purpose of advancing the development and utilization of more energy efficient office equipment. Your attention is drawn to the following actions which could compromise the conformity attested to above, as well as the characteristics of the product: · incorrect electrical power supply; · incorrect installation, incorrect or improper use or use not in compliance with the warnings provided in the User's Manual supplied with the product; · replacement of original components or accessories with others of a type not approved by the manufacturer, or performed by unauthorised personnel. All rights reserved. No part of this material may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording or by any information storage and retrieval system, without permission in writing from the Publisher. CAUTIONS Caution label on the unit The label ( ) in the fusing area of the unit indicates the following: : Caution, risk of danger : Caution, hot surface Cautions on using the unit Follow the cautions below when using this unit. Warning: · The fusing area is hot. Exercise care in this area when removing misfed paper. [. . . ] Gently close the original cover/SPF. Original scale mark 47 Setting a large original (12 cpm model only) The original cover can be removed to allow copying of bulky objects. 1 Simply lift the original cover straight up. 2 To reattach the original cover, reverse the above procedure. Using the SPF The SPF is designed to hold up to 30 originals measuring from A5 to A4 and weighting from 52 to 90 g/m2. · Before feeding originals in the original feeder tray, be sure to remove any staples or paper clips from them. · Before placing curled or wavy originals into the original feeder tray, be sure to flatten them. · The SPF ( ) indicator on the operation panel will light up. If this indicator does not light up, the originals are not properly set or the SPF is not properly closed. · Badly damaged originals may misfeed in the SPF. It is recommended that such originals be copied from the original table. · Special originals such as transparency film should not be fed through the SPF, but should be placed directly on the original table. 4 mm) can occur at the leading and trailing edges of the copies. 4. 5 mm in total) can occur along the other edges of the copies. It can be 6 mm (max. ) at the trailing edge of the second copy of two-sided copying. · To stop continuous copying using the SPF, press the clear ( ) key. 1 2 Make sure that no original is left on the original table. Adjust the original guides to the size of originals. 3 Set the originals face up in the original feeder tray. Original face up 48 Stream feeding mode The stream feeding mode allows easy operation of continuous copying from the SPF. If the stream feeding mode has been enabled using user program No. 4, the SPF ( ) indicator will blink approximately 5 seconds after the last original has been fed by the SPF. While this indicator is blinking, any new originals placed in the original feeder tray will be fed and copied automatically. If the stream feeding mode has been disabled, the start ( ) key must be pressed each time the originals are set even immediately after completion of a copy run from the SPF. The default setting of the stream feeding mode is "ON". See "USER PROGRAMS" (p. 56). SET THE COPY QUANTITY Set the number of copies using the two copy quantity ( from the original table or from the SPF if installed. , ) keys when copying · Press the clear ( ) key to clear an entry if a mistake is made. · A single copy can be made with the initial setting, i. e. , when "0" is displayed. · Press the right copy quantity key to set the unit digit from 0 to 9. This key will not change the tens digit. [. . . ] Upon termination you must destroy the Software and related documentation and all copies thereof. 4. Export Law Assurances. You agree and certify that neither the Software nor any other technical data received from OLIVETTI, nor the direct product thereof, will be exported outside the United States except as authorized and as permitted by the laws and regulations of the United States. If the Software has been rightfully obtained by you outside of the United States, you agree that you will not re-export the Software nor any other technical data received from OLIVETTI, nor the direct product thereof, except as permitted by the laws and regulations of the United States and the laws and the regulation of the jurisdiction in which you obtained the Software. 5. Government End Users. If you are acquiring the Software on behalf of any unit or agency of the United States Government, the following provisions apply. [. . . ]