User manual OLIVETTI D-COPIA 40

[. . . ] In areas of the GEEA, the available setting for the Sleep Mode to engage is between 1 and 120 minutes, and the available setting for the Low Power Mode to engage is any 1 minute, 5 minutes, 15 minutes, 30 minutes, 45 minutes, 60 minutes, 90 minutes or 120 minutes. No part of this material may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording or by any information storage and retrieval system, without permission in writing from the Publisher. It may be prohibited to copy copyrighted material without permission of the copyright owner. It is prohibited under any circumstances to copy domestic or foreign currencies. [. . . ] In addition, the borders of each original can be separated with a solid or dotted line. NOTE: Only standard paper sizes and originals can be used for this. 2 sheets of originals can be copied onto a single sheet. If used together with 2-Sided Copy, 4 sheets of originals can be copied onto both sides of a single sheet. The directions for setting the original and the finished copy are as follows. 4 sheets of originals can be copied onto a single sheet. If used together with 2-Sided Copy, 8 sheets of originals can be copied onto both sides of a single sheet. The directions for setting the original and the finished copy are as follows. NOTE: The 4 in 1 layout setting (refer to 4 in 1 Layout Order on page 417) and the setting of border lines when setting Combine mode (refer to Setting the Combine mode Border Lines on page 4-17) can also be set in the System Menu. The value set in the System Menu will inherit the value that is set at the time when the copy is made. Input the number of sets of copies using the numeric keys. This chapter covers how to configure various settings of the copier using the menus on the operation panel. The copier will enter System Menu after warm up has been completed or when [Reset] has been pressed. the settings automatically set for the copier in System Menu are called the Default Settings. These settings can be freely changed to match the usage of the copier. Change the settings as necessary in order to achieve the most efficient use of the copier. Sets the copy exposure at the time the copier is turned on to Manual or Automatic. There will be no display when Photo Density has been selected in 03. Selects the initial value of the EcoPrint Mode when the power is turned on. the initial value of the Eco Mode can be set to on (Enable). Exposures will be lighter and less toner will be consumed when the EcoPrint Mode is used. Changes the number of the adjustment steps for the copy's exposure. [. . . ] Of Originals that can be loaded Power Source External Dimensions Weight Automatic feed system Sheet originals Maximum: Ledger/A3 Minimum: Statement/A5R Single-side Originals: 45 to 160 g/m2 Double-sided Originals: 50 to 120 g/m2 Less than 50 sheets (50 to 80 g/m2) Electrically connected to the copier main unit Width 21 3/4" × Depth 19 1/8" × Height 4 11/16" Width 552 mm × Depth 483 mm × Height 120 mm Approximately 13. Item Paper Supply System Paper Sizes Acceptable Paper - Paper Weights - Media Types Power Source Dimensions Weight Description Automatic Cassette Feed (sheet storage 300 sheets [80 g/m2]) Ledger, Legal, Letter, Letter R, Statement, Oficio 2, A3, B4, A4, A4R, B5, B5R and A5R 64 to 105 g/m2 Standard paper, recycled paper and color paper Electrically connected to the copier main unit Width 22 7/16" × Depth 21 3/16" × Height 5 5/16" Width 570 mm × Depth 538 mm × Height 135 mm Approximately 15. Standard paper, recycled paper and color paper Electrically connected to the copier main unit Width 14 1/2" × Depth 2 1/16" × Height 7 1/16" Width 368 mm × Depth 53 mm × Height 180 mm Approximately 1. Of Originals that can be read in 100-pin DIMM 16MB, 32MB, 64MB and 128MB 16MB: 250 sheets, 32MB: 250 sheets, 64MB: 250 sheets, 128MB: 250 sheets (Letter, blackness ratio 6% originals) Description Item Recovery time from the Low Power mode Transition time to the Low Power mode (at time of purchase) Transition time to the Sleep modes (at time of purchase) Inch specifications 120V AC 60Hz 10 seconds 15 minutes 30 minutes Metric specifications 220 to 240V AC 50Hz 10 seconds 15 minutes 30 minutes Power consumption in the Plugged-In mode can only be terminated by removing the power plug from the outlet. [. . . ]