User manual OLIVETTI D-COPIA 4501

[. . . ] d-Copia 3501 / 3501MF d-Copia 4501 / 4501MF Operation Manual Be sure to become thoroughly familiar with this manual to gain the maximum benefit from the product. Before installing this product, be sure to read the installation requirements and cautions sections. Be sure to keep all operation manuals handy for reference including this manual, the "Operation manual (for general information and copier operation)" and operation manuals for any optional equipment which has been installed. PUBLICATION ISSUED BY: Olivetti S. p. A. Gruppo Telecom Italia Via Jervis, 77 - 10015 Ivrea (ITALY) www. olivetti. com Copyright 2006, Olivetti All rights reserved The mark affixed to the product certifies that the product satisfies the basic quality requirements. The manufacturer reserves the right to carry out modifications to the product described in this manual at any time and without any notice. ENERGY STAR is a U. S. [. . . ] To divide the pages into sets that can be stapled, select "DIVIDE". If you performed steps 4 to 6 to insert cover paper, divided stapling is not possible. You can either continue pamphlet copying without stapling, or cancel the job. To cancel the pamphlet copy function, touch the [CANCEL] key on the pamphlet copy setting screen (step 7). 5 7 Touch the [OK] key. CANCEL OK G RIGHT BINDING COVER SETTING 8 Touch the [OK] key. OK CANCEL OK Return to the main screen of copy mode. LEFT BINDING RIGHT BINDING COVER SETTING 5-7 SPECIAL MODES Job build Use job build mode when you need to copy more originals than can be placed in the document feeder at once. The maximum number of originals that can be placed in the document feeder at once is 50 sheets (30 sheets when the size is B4 or larger; for more information see "Acceptable originals" on page 4-2). This function lets you divide and scan the originals in sets. This function allows the original pages to be scanned in sets. [Example] Copying 100 pages of A4 originals Originals 1 100 original pages 1 A:50 sheets 51 B:50 sheets *Divide the originals into sets of 50 pages each. Scan the originals starting from the first page of set A. Scan set B next, taking care to keep the correct page order. To display the special modes screen. . . See "General procedure for using special functions" on page 5-2. that is 4 Make sureselect the desired paper size or selected, the number of copies other copy settings, and [START] key. press the 1 Touch the [JOB BUILD] key on the special modes screen. ES DUAL COP TANDE COPY N SHIFT ERASE LET COPY JOB BUILD The [JOB BUILD] key will be highlighted to indicate that the function is turned on, and the job ) will build icon ( appear in the upper left of the screen. Scanning of originals will start. After scanning of the first set of originals (A in the example above) is completed, remove the scanned originals, place the next set of originals (set B in the example) and press the [START] key. Repeat this operation until all sets of originals have been scanned. 2 RASE Touch the [OK] key on the special modes screen. OK 5 Touch the [READ-END] key. PLACE NEXT ORIGINAL. READ-END Return to the main screen of copy mode. 1/3 DUAL PAGE COPY TANDEM COPY JOB BUILD first 3 Place the feederset of originals document tray. (page 4-3) in the To cancel the job build function, touch the [JOB BUILD] key on the special modes screen (step 1). The highlighted display will be cancelled. 5-8 SPECIAL MODES Tandem copy Two machines connected to the same network can be used to run a large copy job in parallel. By dividing the job in half, approximately half the time is required to complete the job. To use this function, two machines must be connected to your network as network printers. Even if more machines are connected to the network, this function can only be used to have one other machine share a job. Server machine and client machine In the following explanations, the machine on which the copy job is initially set up and tandem copy selected is called the server machine. The other machine that is asked to share the job is called the client machine. [. . . ] 3-4 -Finisher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13 -General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23 to 2-25 -Saddle stitch finisher. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24 Types and sizes of paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]