User manual OLIVETTI D-COPIA 8200

[. . . ] The following items are normally prohibited from copying by national law. Other items may be prohibited by local law. Money Checks Stamps Passports Bonds Stocks Bank drafts Driver's licenses In some areas, the "POWER" switch positions are marked "I" and " " on the copier instead of "ON" and "OFF". If your copier is so marked, please read "I" for "ON" and " " for "OFF". [. . . ] The ROPM function stores multiple pages of print data in memory before printing. When printing multiple copies, this eliminates the need for the computer to repeatedly transmit the print data. · If a problem occurs in printer mode, see "TROUBLESHOOTING". (p. 48) · Two printer drivers are provided for the machine: a standard printer driver and a printer driver that is used when the dual function board is installed. Install the correct printer driver depending on whether or not the dual function board is installed. If the correct printer driver is not used, printing may not take place correctly. (See the "Software Setup Guide" for information on installing the printer drivers. ) · When using USB 2. 0 (Hi-Speed mode), be sure to read "System requirements for USB 2. 0 (Hi-Speed mode)" (below) to verify that your system and the machine settings are configured appropriately. · Do not install the printer driver for the dual function board when the dual function board is not installed. If this is done, a warning message will be printed out, and the print job will be cancelled. · When interrupt copying is being performed, printing is not possible. System requirements for USB 2. 0 (Hi-Speed mode) The following system is required to use USB 2. 0 (Hi-Speed mode): · Your computer must be running Windows XP / Windows 2000 and the Microsoft USB 2. 0 driver must be pre-installed, or the USB 2. 0 driver for Windows XP / Windows 2000 must be installed using Microsoft's Windows Update service. · The "USB 2. 0 mode switching" setting in the machine's user programs must be set to "Hi-Speed". ) is pressed after the copy job is finished, or when the [ON LINE] key ( ) is *2 Printing will begin when the [CLEAR ALL] key ( pressed to switch the machine online. Printing will also begin after the set auto clear time elapses, or after 60 seconds if "Auto clear time" is disabled. *3 The print job is paused and copying begins. 4 37 5 Note Chapter 5 USER SETTINGS This chapter explains how to set the automatic exposure level, toner save mode/high image quality mode, and the user programs, which are custom settings that control fine points of the machine's operation. ADJUSTING THE AUTOMATIC EXPOSURE LEVEL The exposure level used in automatic exposure adjustment, which automatically adjusts the copy exposure according to the original, can be adjusted. If copies tend to be too dark or too light when automatic exposure adjustment is used, follow the steps below to adjust the automatic exposure level. The automatic exposure level can be adjusted separately for the document glass and the SPF. The copy and printer cannot be used while the automatic exposure level is being adjusted. 1 To adjust the automatic exposure level in the SPF, place the original in the SPF. (p. 19) Make sure that the SPF indicator is lit. To adjust the automatic exposure level for copies made from originals placed on the document glass, proceed to step 2. 4 Press the [Light] key ( ) or [Dark] key ( ) to lighten or darken the automatic exposure level as desired. 135 Note 2 3 Press the [AUTO/TEXT/PHOTO] key ( AUTO / / ) to select "PHOTO" ( ). Hold down the [AUTO/TEXT/PHOTO] key ( AUTO / / ) until the AUTO indicator ( AUTO ) blinks. AUTO 5 Press the [AUTO/TEXT/PHOTO] key ( AUTO / / ) to complete the setting. The AUTO indicator ( AUTO ) stops blinking and lights steadily. 135 The exposure level indicators show the current setting. Note After adjusting the automatic exposure level, it is recommended that you make a test copy to check the new level. 38 TONER SAVE MODE AND HIGH IMAGE QUALITY MODE Toner save mode can be enabled to reduce toner consumption by about 10%. The high image quality mode improves copy image quality in the automatic and manual exposure modes by increasing copy density with a slight increase of toner consumption. To switch between toner save mode and high image quality mode, follow the steps below. Note In Europe, high image quality mode is initially selected. In regions other than Europe, toner save mode is initially selected. 1 Press the [AUTO/TEXT/PHOTO] key ( AUTO / / ) to select "TEXT" ( ). Hold down the [AUTO/TEXT/PHOTO] key ( AUTO / / ) until the PHOTO indicator ( ) blinks. AUTO 2 135 The exposure level indicators show the current setting. 3 To enable toner save mode, press the [Light] key ( ). [. . . ] 30 Machine settings Auditing mode - Copies, how to make. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 - Setting procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 - Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Automatic exposure level, setting . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]