User manual OLIVETTI D-COPIA 3000MF SETUP GUIDE

[. . . ] d-Copia 2500MF d-Copia 3000MF Operation Guide Cod 539209en PUBLICATION ISSUED BY: Olivetti S. p. A. Gruppo Telecom Italia Via Jervis, 77 - 10015 Ivrea (ITALY) www. olivetti. com Copyright © 2007, Olivetti All rights reserved The mark affixed to the product certifies that the product satisfies the basic quality requirements. The manufacturer reserves the right to carry out modifications to the product described in this manual at any time and without any notice. ENERGY STAR is a U. S. registered mark. The ENERGY STAR program is an energy reduction plan introduced by theUnited States Environmental Protection Agency in response to environmental issues and for the purpose of advancing the development and utilization of more energy efficient office equipment. Your attention is drawn to the following actions which could compromise the conformity attested to above, as well as the characteristics of the product: · incorrect electrical power supply; · incorrect installation, incorrect or improper use or use not in compliance with the warnings provided in the User's Manual supplied with the product; · replacement of original components or accessories with others of a type not approved by the manufacturer, or performed by unauthorised personnel. All rights reserved. No part of this material may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording or by any information storage and retrieval system, without permission in writing from the Publisher. Introduction Thank you for your purchase of d-Copia 2500MF, d-Copia 3000MF This Operation Guide is intended to help you operate the machine correctly, perform routine maintenance and take a simple troubleshooting action as necessary, so that you can always use the machine in good condition. [. . . ] Model Inch Models Zoom Level (OriginalCopy) 100%, Auto, 400% (Max. ), 200% (STMT -> Ledger), 154%(STMT -> Legal), 129% (Letter -> Ledger), 121% (Legal -> Ledger), 78% (Legal -> Letter), 77% (Ledger -> Legal), 64% (Ledger -> Letter), 50% (Ledger -> STMT), 25% (Min. ) OPERATION GUIDE 3-13 Basic Operation Model Metric Models Zoom Level (OriginalCopy) 100%, Auto, 400% (Max. ), 200% (A5 -> A3), 141% (A4 -> A3, A5 -> A4), 127% (Folio -> A3), 106% (11×15" -> A3), 90% (Folio -> A4), 75% (11×15" -> A4), 70% (A3 -> A4, A4 -> A5), 50%, 25% (Min. ) 100%, Auto, 400% (Max. ), 200% (A5 -> A3), 141% (A4 -> A3, B5 -> B4), 122% (A4 -> B4, A5 -> B5), 115% (B4 -> A3, B5 -> A4), 86% (A3 -> B4, A4 -> B5), 81%(B4 -> A4, B5 -> A5), 70% (A3 -> A4, B4 -> B5), 50%, 25% (Min. ) Metric Models (Asia Pacific) XY Zoom Select vertical and horizontal magnifications individually. Reduce or enlarge original images in 1% increments between 25% and 400%. Y X The procedure for using zoom copying is explained below. 1 Set the original on the platen and press [Layout/Edit] -> [Zoom]. Ready to copy. Copy Image Zoom Combine Margin/ Centering Copies 1 Border Erase Set Original. Booklet Duplex Cover Form Overlay Original Zoom Paper : -- : 100% : -- Preview Page # Memo Page Quick Setup Status Org. /Paper / Finishing Image Quality Layout /Edit Advanced Setup 10/10/2007 10 :10 3-14 OPERATION GUIDE Basic Operation 2 Press [Standard Zoom] to use Auto Zoom. Press [+] or [­] to change the displayed magnification as desired. You can also enter the magnification directly using the numeric keys by pressing [# Keys]. When using Preset Zoom, select the key of desired magnification. When using XY Zoom, press [XY Zoom]. Ready to copy. Zoom Standard Zoom Press [ OK] to display the image. (25 - 400) Legal >>Letter Ledger >>Legal Ledger >>Letter Ledger >>STMT Copies 1 3 78% # Keys 100% Auto 77% 64% 50% STMT 200% >>Ledger 154% STMT >>Legal Letter 129% >>Ledger Legal 121% >>Ledger Min. 25% Press [+] or [­] to change the Add Shortcut Cancel OK displayed magnifications of X (horizontal) and Y (vertical). You can also enter the magnification directly using the numeric keys by pressing [# Keys]. Status 10/10/2007 10 :10 Press [Original Orientation] to select orientation of the originals, either [Top Edge Top] or [Top Edge Left]. Then press [OK]. Ready to copy. Zoom Standard Zoom Press [ OK] to display the image. Y XY Zoom # Keys (25 - 400) % X (25 - 400) % Copies 1 Top Edge Top # Keys Add Shortcut Status Original Orientation Cancel OK 10/10/2007 10 :10 3 4 Press [OK]. Copying begins. OPERATION GUIDE 3-15 Basic Operation Duplex Copying Produce two-sided copies. The following duplex options are available. One-sided to Two-sided Produces two-sided copies from one-sided originals. In case of an odd number of originals, the back side of the last copy will be blank. 5 4 3 3 5 4 1 2 2 1 Original Copy The following binding options are available. A Original Left/Right to Binding Left/Right: Images on the second sides are not rotated. B Original Left/Right to Binding Top: Images on the second sides are rotated 180°. Copies can be bound on the top edge, facing the same orientation when turning the pages. ghi def abc A abc ghi B ghi abc def Original def Copy Two-sided to One-sided Copies each side of a two-sided original onto two individual sheets. The optional document processor is required. 1 1 2 Original 2 Copy The following binding options are available. · · Binding Left/Right: Images on the second sides are not rotated. Binding Top: Images on the second sides are rotated 180º. 3-16 OPERATION GUIDE Basic Operation Two-sided to Two-sided Produces two-sided copies from two-sided originals. [. . . ] 12 Display/Key [ ]/[ ] Description To enter a number or symbol not shown in the keyboard, press the cursor key and scroll the screen to view other numbers or symbols to enter. OPERATION GUIDE Appendix-3 Entering Characters Follow the steps shown below to enter List A-1 for example. 1 2 Press [Upper-case]. The letter L is shown on the display. Path Use the keyboard to enter. Limit: 126 characters Input : 1 characters Backspace L Upper -case Lower-case No. /Symbol Space Cancel OK 3 4 Press [Lower-case]. Press [i], [s], [t] and [Space]. Path Use the keyboard to enter. [. . . ]