User manual OLYMPUS CAMEDIA C-3000

[. . . ] In the interest of continually improving products, Olympus reserves the right to update or modify information contained in this manual. For customers in North and South America For customers in USA Declaration of Conformity Model Number : C-765 Ultra Zoom Trade Name : OLYMPUS Responsible Party : Olympus America Inc. Address : 2 Corporate Center Drive, Melville, New York 11747-3157 U. S. A. Telephone Number : 1-631-844-5000 Tested To Comply With FCC Standards FOR HOME OR OFFICE USE This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. [. . . ] This is useful when you want to check shooting results and resume shooting quickly. Functions available in normal playback mode are also available in QUICK VIEW. Mode dial 1 Press the QUICK VIEW button in the shooting mode. · The camera immediately enters the playback mode and displays the last picture taken. (Single-frame playback) Shutter button 72 Playback Press the QUICK VIEW button again to return to the shooting mode. · You can also return to the shooting mode when the shutter button is gently pressed. 114 Close-up playback Pictures displayed on the monitor can be enlarged 1. 5, 2, 2. 5, 3, 3. 5 or 4 times. Mode dial 1 Select the still picture you want to enlarge. g"Viewing still pictures" (P. 113) · You cannot enlarge pictures with n. Zoom lever 2 Pull the zoom lever toward T (U). · Each time you pull the zoom lever, the picture is enlarged gradually. · By using the arrow pad while the enlarged picture is displayed, you can shift the picture in the desired direction, enabling you to view a different portion. · To return the picture to the original size (1×), push the zoom lever toward W. 7 Playback '04. 06. 17 15:30 '0 17 30 · Pictures cannot be stored in an enlarged state. Note 115 Index display This function lets you show several pictures at the same time on the monitor. The number of pictures shown can be 4, 9 or 16. g"Selecting the number of pictures" (P. 117) Mode dial 1 In the single-frame playback mode, push the zoom lever toward W (G). g"Viewing still pictures" (P. 113) · Use the arrow pad to select the picture. a : Jumps to the previous index display (the frames before the top left frame). c : Jumps to the next index display (the frames following the bottom right frame). · To return to the single-frame playback, pull the zoom lever toward T. Zoom lever 7 Playback 116 Index display Selecting the number of pictures This function lets you select the number of pictures in an index display from 4, 9 and 16. Mode dial 1 In the top menu, select MODE MENU SETUP G 4, 9 or 16, and press e. g"How to use the menus" (P. 33) · Press e again to exit the menu. Arrow pad OK button SEtUP CARD EDIt PLAY VIDEO OUt 4 9 16 7 Playback 117 Slideshow This function displays still pictures stored in the card one after another. Only the first frame of movies is played back. Mode dial 1 Select a still picture, then press e to display the top menu. g"Viewing still pictures" (P. 113) a button e button 2 Press a to start the slideshow. INFO MODE MENU SWItCH FRAME 73 Playback Press e to stop the slideshow. · The slideshow will not stop until you cancel it by pressing e. '04. 06. 17 15:30 '0 17 30 Note · You are recommended to use the optional AC adapter when running a slideshow for a long period of time. GO SELECt · If you want to select different frames, select RESET and press e and repeat the procedure from Step 4. · To quit the editing function, select CANCEL and press e. TIPS · The index is stored as a still picture in a different record mode from the original movie. Record mode when the movie was shot SHQ HQ SQ Record mode when stored as an index SQ2 (1024 × 768 pixels: HIGH) SQ2 (1024 × 768 pixels: HIGH) SQ2 (640 × 480 pixels: HIGH) 122 Editing movies Note · The interval between the frames that are automatically picked out varies depending on the length of the movie. · You cannot create an index if there is insufficient memory space on the card. EDIT - Editing a movie 3 Press ac to select EDIT, then press e. MOVIE PLAY MOVIE PLAYBACK INDEX EDIt 4 CANCEL SELECt GO Use the arrow pad to select the first frame of the part you want to keep and press e. 00:00 00:36 a : Jumps to the first frame of the movie. c : Jumps to the last frame of the movie. The movie GO can be played continuously by holding the button down. The movie can be played continuously in reverse by holding the button down. 7 Playback 5 As in Step 4, use the arrow pad to select the last frame of the part you want to keep and press e. GO 00:36 00:36 123 Editing movies 6 Press ac to select OK, then press e. · If you want to select different frames, select RESET and press e and repeat the procedure from Step 4. · To quit the editing function, select CANCEL and press e. EDIt OK RESEt CANCEL SELECt EDIt NEW FILE OVERWRItE CANCEL SELECt GO GO 7 Press ac to select NEW FILE or OVERWRITE, then press e. NEW FILE Stores the edited movie as a new movie. OVERWRITE Stores the edited movie with the same name as the original. The original movie is not stored. · The edited movie is stored and the screen returns to the playback mode. 7 Playback Note · You cannot edit movies with sound which were taken with another digital camera. · You cannot select NEW FILE if there is insufficient memory space on the card. [. . . ] The files will be opened in the default image viewer of the operating system. If you want to view the image a different size or process it, you will need to open the image with software that supports JPEG or TIFF images files, such as Paint Shop Pro, Photoshop or CAMEDIA Master software. The lamp on the right of the viewfinder or the card access lamp blinks while the image is being copied. Never open the card cover on the camera, load or remove the batteries, or connect or disconnect the AC adapter while the lamp is blinking as the image files may be destroyed. Macintosh 28 Downloading images to your computer Mac OS X Malfunctions such as the following may occur due to the OS. [. . . ]