User manual OLYMPUS CAMEDIA D-500L

[. . . ] Screen and camera illustrations shown in this manual may differ from those of the actual product. For customers in North and South America For customers in USA Declaration of Conformity Model Number : D-580ZOOM/C-460ZOOM/X-400 Trade Name : OLYMPUS Responsible Party : Olympus America Inc. Address : 2 Corporate Center Drive, Melville, New York 11747-3157 U. S. A. Telephone Number :1-631-844-5000 Tested To Comply With FCC Standards FOR HOME OR OFFICE USE This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. [. . . ] in HQ mode Longer than approximately 2 min. in SQ mode Movies with sound : Longer than approximately 30 sec. in HQ mode Longer than approximately 2 min. in SQ mode INDEX 9 frames extracted from a movie are displayed as an index to show the movie at a glance. Indexes can be stored on the card as a still picture. EDIT This function lets you erase parts of the movie that you do not want. 1 Press closed. with the lens barrier Playback button ( ) · The monitor turns on. 2 Use the arrow pad to select a picture with . OK button 5 Playback Arrow pad 3 Press . · The top menu is displayed. 4 In the top menu, select MODE MENU EDIT, and choose each item. "How to use the menus" (P. 33) · Select INDEX · Select EDIT P. 102 P. 103 101 Editing movies INDEX - Creating an index 5 6 Select INDEX, and press . Select the first frame of the index. Press the arrow pad to play back the movie until the picture that you want as the first frame is displayed in the green frame at the upper left corner, and press . 7 OK Select the last frame of the index. As in Step 6, press the arrow pad to play back the movie until the picture that you want as the last frame is displayed in the green frame at the lower right corner, and press . OK 5 Playback 8 Press press to select OK, and . INDEX OK · The 9 frames extracted from the movie appear as an index display, and the RESEt camera returns to the playback mode. The CANCEL index is stored as a new picture. GO SELECt · If you want to select the frames again, select RESET and press and repeat the procedure from Step 6. · To cancel the index function, select CANCEL and press . TIPS · The index is stored as a still picture in a different record mode from the original movie. Record mode when the movie is shot HQ SQ Record mode when stored as an index 1024 x 768 pixels 640 x 480 pixels 102 Editing movies Note · The interval between the frames that are automatically picked out varies depending on the recording time of the movie. · You cannot create an index if there is insufficient memory space on the card. EDIT - Editing a movie 5 Select EDIT, and press . 6 Use the arrow pad to select the first frame of the part you want to keep and press . : Jumps to the first frame of the movie. The movie can OK be played continuously by holding the button down. "With print reservation" (P. 119) 109 Adjusting the monitor brightness This function lets you adjust the brightness of the monitor. The brightness can be adjusted in either the shooting mode or the playback mode. 1 In the top menu, select MODE MENU SETUP , and press . "How to use the menus" (P. 33) OK button 2 Arrow pad Press to adjust the brightness of the monitor, and when you have set the desired level, press . · Pressing brightens the monitor, and pressing darkens it. · Press again to exit the menu. ADJUSt GO 6 Useful functions 110 REC VIEW You can choose whether or not to have the picture you have just taken displayed briefly on the monitor. ON : The picture being recorded to the card is displayed. This is useful for making a quick check of the picture you have just taken. You can resume shooting anytime during REC VIEW. : The picture being recorded to the card is not displayed. This is useful when you want to prepare for your next shot while the previous picture is being recorded. OFF 1 In the shooting mode top menu, select MODE MENU SETUP REC VIEW OFF or ON, and press . "How to use the menus" (P. 33) OK button Arrow pad · Press again to exit the menu. 6 Useful functions · If the batteries are running low when you take a picture with the monitor off and REC VIEW is set to ON, the picture may not be displayed. Note 111 Turning off the operation and beep sound This function lets you turn on/off the beep sound used for warnings, etc. The beep sound can be adjusted in either the shooting mode or the playback mode. 1 In the top menu, select MODE MENU SETUP OFF or ON, and press . "How to use the menus" (P. 33) OK button Arrow pad · Press again to exit the menu. 6 Useful functions 112 PW ON/OFF SETUP - Power on/off display setting You can select a picture to be displayed on the monitor when turning the camera on or off. It is also possible to register your favorite picture. g"SCREEN SETUP" (P. 114) 1 In the top menu, select MODE MENU SETUP PW ON/OFF SETUP, and press . "How to use the menus" (P. 33) OK button 2 Arrow pad Press then press to select OFF, 1 or 2, . OFF No picture is displayed. [. . . ] · When file number 9999 is reached, a new folder is created and assigned the next number. · Months January through September are expressed by the numbers 1 through 9, October by the letter A, November by B and December by C. Macintosh 4 Double-click the "Macintosh HD" icon on the desktop. 27 Downloading images to your computer The "Hard Disk" window is displayed. 5 Drag & drop the image you want to save in the computer (in this case, P1010012. JPG) to the "Hard Disk" window. The image is saved in the computer (in the Hard disk). · To select all images, click Edit > Select all. When the image file has been copied to the computer, you can view images by double-clicking the image files in the "Hard Disk" folder. [. . . ]