User manual OLYMPUS PER-E02

[. . . ] These pictographs and their meanings are shown below. WARNING CAUTION Please pay particular attention to this information. If ignored when using the product, there is a risk of serious injury and even death. Ignoring this information when using the product could lead to injury or material damage. WARNING This product should be kept out of reach of infants and children to prevent accidents such as the following: · Injury caused by the product falling from a height and striking the body from a height. [. . . ] Underwater zooming is possible when the zoom gear, provided with this product, is attached to the lens. However, only AF (auto focus) focusing is available. E-1 1 Name of Parts PER-E02 main body Silicon O-ring (POL-E101) Front cap Rear cap PT-E series waterproof case mount Grease for silicone O-ring Pick for O-ring removal Waterproof lens port mount Zoom gear * This product has been designed for exclusive use with the following ZUIKO DIGITAL lens. This product should also be used in combination with the separately available PPO-E04 Underwater Lens Port. Applicable lens Applicable underwater lens port ZUIKO DIGITAL ED 7-14 mm F4. 0 PPO-E04 2 Mounting the PER-E02 between the Waterproof Case and the Waterproof Lens Port Threaded section O-ring PPO-E04 Silicone grease application surfaces Threaded section O-ring PER-E02 Surface coming in contact with the lens port's O-ring/ Port mount thread O-ring contact surfaces Port mount thread PT-E series waterproof case This product is designed to be mounted between the PT-E series underwater case and the PPO-E04 Underwater Lens Port. Before mounting, make sure that no foreign matter is attached to the O-rings, O-ring contact surfaces, port mount threads or threaded sections of the three modules. Apply a thin layer of the provided silicone O-ring grease to each of these parts. E-2 Align the threaded section of the PER-E02 with the port mount thread on the PT-E series case. Hold the PT-E series case firmly with one hand, hold the main body of the PER-E02 with your other hand and screw it into the PT-E series by turning the PER-E02 clockwise. Resistance increases as the PER-E02 is screwed in more deeply. However, be sure to screw it in all the way until there is no gap visible between the case's port mount thread and the PER-E02's threaded section. If the resistance is extremely high, apply some more silicone O-ring grease again to surfaces listed above. Screw in until there is no gap. Align the lens port mount thread of the PER-E02 with the threaded section on the PPO-E04 lens port. Hold the PT-E series case and PER-E02 firmly with one hand, hold the main body of the PPO-E04 lens port with your other hand and turn it clockwise to screw it into the PER-E02. Resistance will increase as the PPO-E04 lens port is screwed in However, be sure to screw it in all the way until there is no gap visible between the PPO-E04 lens port's thread section and the PER-E02's port mount thread. If the resistance is extremely high, apply some more silicone O-ring grease again to surfaces listed above. Screw in until there is no gap. E-3 3 Dismounting the PER-E02 If any water is on the product, wipe it completely away and make sure that the product is dry. Holding the PT-E series case firmly with one hand, loosen the PPO-E04 lens port that is attached to the PER-E02 by turning the lens port about 90 degrees counterclockwise. If the PPOE04 is screwed in too tight, wrap it with a piece of rubber or other slip-resistant material. After loosening the PPO-E04 lens port, position it so that its lens points down and turn it further counterclockwise until it separates from the PER-E02. [. . . ] To apply grease to each O-ring, squeeze a drop of grease about the size of a grain onto your finger and lightly rub the entire circumference of the O-ring to spread the grease thinly and evenly. E-7 6 Specifications Applicable case : PT- E series Corresponding lens port : PPO-E04 Applicable lens : ZUIKO DIGITAL ED 7-14mm F4. 0 Main materials Main body : Aluminum. Withstanding pressure : Water depth of 60 m (200 ft) Dimensions : Max. diameter 108 mm x Depth 75. 6 mm Weight : Approx. [. . . ]