User manual OLYMPUS PPO-E03

[. . . ] To ensure correct and safe use of this product, always use it as described in this instruction manual. For safe use This instruction manual uses pictographs to show how to use the product correctly and how to prevent danger to the user and other persons as well as damage to property. These pictographs and their meanings are shown below. WARNING CAUTION Please pay particular attention to this information. If ignored when using the product, there is a risk of serious injury and even death. [. . . ] To control manual focus (MF) operation from this product, the provided gear must be attached to the MF ring on the lens. Attach the gear to the MF ring on the lens as instructed in this manual. E-1 1 Name of Parts PPO-E03 main body Silicon O-ring (POL-E101) Front cap Rear cap MF Gear Grease for silicone O-ring Pick for O-ring removal 2 Mounting the PPO-E03 on the Waterproof Case Grease applying surface on O-rings Threaded section O-ring This section describes how to mount this product on the PT-E series case. Before mounting, check that no foreign matter is attached to the O-rings, the port mount thread on the PT-E series case, or the Oring contact surfaces. Apply a thin layer of the provided silicone O-ring grease. O-ring contact surfaces Port mount thread Align the threaded section of the PPO-E03 with the port mount thread on the PT-E series case. Hold the PT-E series case firmly with one hand, hold the main body of the PPO-E03 with your other hand and screw it into the PT-E series by turning the PPO-E03 clockwise. Resistance increases as the PPO-E03 is screwed in more deeply. However, be sure to screw it in all the way until there is no gap visible below the threaded section of the PPO-E03. Screw in until there is no gap. E-2 3 Dismounting the PPO-E03 If any water is on the product, wipe it completely away and make sure that the product is dry. Holding the PT-E series case firmly with one hand, loosen the PPO-E03 by turning it about 90 degrees counterclockwise. If the PPO-E03 is attached too tightly to turn, wrap it with a piece of rubber or similar non-slip material. After loosening the PPO-E03, point its lens downward and turn it further counterclockwise until it is separated from the PT-E series case. Be careful not to drop the PPO-E03 or PT-E series case. CAUTION: While dismounting the PPO-E03 from the case, water remaining on the PPO-E03 may splatter on the lens or camera. If this happens, wipe the water off the lens and camera with a dry cloth. Make sure that the port is completely dry before dismounting. E-3 4 Attaching the Gear to the Lens To control the camera lens's manual focus (MF) operation, the provided gear must be attached to the MF ring on the lens. * Note that this will restrict the rotation range of the MF ring to within 180°. Confirm the position of the gear's lock dial and hinge. Turn the lock dial counterclockwise to release the lock and open the gear. Hinge Open Lock dial Gear Open the gear all the way, place it on the lens and adjust the rotation direction of the gear. [. . . ] Also remove any foreign matter from the O-ring contact surfaces and from the port mount thread on the PT-E series case. After removing foreign matter, apply the provided grease to the O-rings and fit them into the O-ring grooves. To apply grease to each O-ring, squeeze a drop of grease about the size of a grain onto your finger and lightly rub the entire circumference of the O-ring to spread the grease thinly and evenly. E-7 7 Specifications : PT-E series : ZUIKO DIGITAL ED 50mm F2. 0 Macro : Aluminum. diameter 108 mm x Depth 87 mm : 420 g (excluding the conversion lens) Applicable case Applicable lens Main materials Main body Lens window O-rings MF gear Front cap Rear cap Withstanding pressure Dimensions Weight Note) We reserve the right to change the external appearance and specifications without notice. 8 Consumable Items Product Model POL-E101 Product Model PSOLG- 1 Description O-ring for use with the PT-E series case. [. . . ]