User manual OLYMPUS PT-050

[. . . ] PT-050 PT-050 Instruction Manual http://www. olympus. com/ ©2011 Printed in China VR348902 En Thank you for buying the Underwater Case PT-050 (hereinafter Case). Please read this instruction manual carefully and use the product safely and correctly. Please keep this instruction manual for reference after reading it. Wrong use may cause damage to the camera inside the Case due to water leakage, and repair may not be possible. [. . . ] Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 EN 7 1. Preparations Check the contents of the package. En Check that all accessories are in the box. Contact your dealer if accessories are missing or damaged. · LCD hood (on the body) · LCD hood strap · Silicone grease · Silica gel (1g) · Lens cap · O-ring remover · Hand strap · Diffuser · Case body (Check that the O-ring is installed) (Port adaptor) · Instruction manual (this manual) · OLYMPUS distributor list EN 8 Names of the parts 3 2 4 5 En 6 1 7 8 9 c b a 0 1 *2 *3 *4 Palm grip Zoom lever Shutter lever ON/OFF button 5 6 7 8 Accessory mount Front lid Open/close dial Lens ring *9 0 a b c Control dial O-ring Tripod seat Light shield hood LCD inner hood EN 9 d e o En f g h i n *d *e *f *g q button Mode dial ( (REC) button F button/arrow pad *h *i *j *k m lkj # button/Arrow pad *l MENU button OK button *m & button/Arrow pad INFO button n LCD monitor window AFL/ button/arrow pad o Rear lid Memo: The Case operation parts marked by * corresponds to the operation parts of the digital camera. When the operation parts of the Case are operated, the corresponding functions of the digital camera will operate. For details of the functions, refer to the instruction manual for the digital camera. EN 10 Using the accesories Install the strap Install the strap on the Case body. Installation illustration Installation completed En Hand strap Hand strap ring How to use the hand strap Pass your hand through the hand strap and adjust the length with the stop button. stop button EN 11 Installation and removal of the LCD hood Installation Fit the LCD hood as shown in the figure into the guides above and below the LCD monitor window one after the other. Removal Remove the LCD hood from the guides above and below the LCD monitor window one after the other by widening the LCD hood. En Guides Installation Removal Mounting and removing the lens cap Fit the lens cap onto the lens ring as shown in the figure. Be sure to remove the lens cap before shooting. EN 12 Using the diffuser 1 Install the hand strap on the Case body. En 2 Install the diffuser on the Case. Install to fit together the convex part of the port adaptor on the diffuser and the concave part of the port on the Case. Port adaptor Mounting and removing the port adaptor and diffuser Fit the mark on the side of the strap hole, then assemble the parts. When removing, be sure to remove the part finally. mark EN 13 2. Advance Check of the Case Advance check before use En This Case has been the subject of thorough quality control for the parts during the manufacturing process and thorough function inspections during the assembly. 2 Turn the open/close dial to the position where it cannot be turned further. 3 Open the rear lid of the Case gently. En 1 Slide lock 2 Open Open/close dial CAUTION: Do not exert too much force while turning the open/close dial. Doing so may damage the dial. Pop up the flash When the camera is in the Case, attach the diffuser if you use only the camera's built-in flash. Be sure to pop up the flash when you use the underwater flash. EN 16 Load the digital camera 1 Confirm that the digital camera is OFF. 2 Gently insert the digital camera into the Case. 3 Insert piling up silica gel bag (1g) between the bottom of the digital camera and the Case. The silica gel bag provided for prevention of fogging. 2 En 3 CAUTION: · The silica gel bag will be caught when the Case is sealed and water leakage will occur. · Once silica gel has been used, the moisture absorption performance will be impaired. Always replace the silica gel when the Case is opened and closed. Make sure the camera is loaded properly Check the following points before sealing the Case. · Is the digital camera loaded properly?· Is silica gel inserted all the way at the specified location? [. . . ] Also remove any sand or dirt adhered to the O-ring contact surface on the front lid of the case. En CAUTION: · Maintenance of the waterproof functions is required even before using this product underwater for the first time. · When a sharp object is used to remove the O-ring or to clean the inside of the O-ring groove, the Case and the O-ring may be damaged and water leakage may occur. · Take care not to stretch the O-ring. · Never use alcohol, thinner, benzene or similar solvents or chemical detergents to clean the O-ring. [. . . ]