User manual OLYMPUS PT-051

[. . . ] PT-051 PT-051 Instruction Manual http://www. olympus. com/ ©2011 Printed in China VR541601 En Thank you for buying the Underwater Case PT-051 (hereinafter Case). Please read this instruction manual carefully and use the product safely and correctly. Please keep this instruction manual for reference after reading it. Wrong use may cause damage to the camera inside the Case due to water leakage, and repair may not be possible. [. . . ] 28 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 En EN 7 1. Preparations Check the contents of the package. En Check that all accessories are in the box. Contact your dealer if accessories are missing or damaged. · LCD hood (on the body) · LCD hood strap · Silicone grease · Optical fiber cable adapter · Silica gel (1g) · Lens cap · Hand strap · Case body (Check that the O-ring is installed) · O-ring remover · Adapter PTAC-09 (for TOUGH TG-810) · Adapter PTAC-08 (for TOUGH TG-610) · Instruction manual (this manual) · OLYMPUS distributor list EN 8 Names of the parts 3 4 5 En 2 1 6 7 8 9 a 0 1 2 *3 *4 Palm grip Diffuser Shutter lever ON/OFF button 5 6 7 8 Accessory mount Front lid Open/close dial Lens ring 9 LCD inner hood 0 O-ring a Tripod seat EN 9 b c d e En f g h m *b *c *d *e *f *g *h E button ( (REC) button Zoom buttons q button MENU button INFO button/arrow pad Arrow pad l kj i *j button/arrow pad *k Arrow pad l LCD monitor window m Rear lid *i OK/AFL button (*1) (*1) During Underwater WideAngle 1 or Underwater Macro shooting mode, the OK button functions as the AF LOCK button. Memo: The Case operation parts marked by * corresponds to the operation parts of the digital camera. When the operation parts of the Case are operated, the corresponding functions of the digital camera will operate. For details of the functions, refer to the instruction manual for the digital camera. EN 10 Using the accesories Install the strap Install the strap on the Case body. Installation illustration Installation completed En Hand strap Hand strap ring How to use the hand strap Pass your hand through the hand strap and adjust the length with the stop button. stop button EN 11 Installation and removal of the LCD hood Installation Fit the LCD hood as shown in the figure into the guides above and below the LCD monitor window one after the other. Removal Remove the LCD hood from the guides above and below the LCD monitor window one after the other by widening the LCD hood. En Guides 1 1 2 Installation 2 Removal Mounting and removing the lens cap Fit the lens cap onto the lens ring as shown in the figure. Be sure to remove the lens cap before shooting. EN 12 Using the fiber cable adapter The fiber cable adapter is required when connecting the separately available UFL-1 underwater flash to the Case using an underwater optical fiber cable (optional: PTCB-E02). How to install 1 Attach the optical fiber cable adapter to the diffuser shown in the figure below. En 2 Put the underwater optical fiber cable plug all the way into the optical fiber cable (optional: PTCB-E02) insertion slot. Remove the underwater optical fiber cable when you do not use it while taking picture. Memo: RC mode can use only TOUGH TG-810. Remove the hand strap from the digital camera. When a digital camera is loaded without removing the strap, the strap may get caught between the Case lids and may cause water leakage. Attach the adapter to the digital camera Attach the digital camera while distending the adapter slightly. * The above illustration is for PTAC-09. Adapter PTAC-08 Adapter PTAC-09 . for TOUGH TG-610 for TOUGH TG-810 CAUTION: When combination of the digital camera and the adapter is incorrect, the camera does not operate correctly. Be sure to check the combination while installing the digital camera. EN 15 Open the Case 1 Slide and hold the slide lock towards the arrow direction (1 of figure below) and turn the open/close dial counter clockwise (2 of figure below). 2 Turn the open/close dial to the position where it cannot be turned further. 3 Open the rear lid of the Case gently. En 1 Slide lock 2 Open Open/close dial CAUTION: Do not exert too much force while turning the open/close dial. Doing so may damage the dial. EN 16 Load the digital camera 1 Confirm that the digital camera is OFF. 2 Gently insert the digital camera which has attached the adapter into the Case. 3 Insert 2 piling up silica gel bags (1g) between the bottom of the digital camera and the Case. The silica gel bag provided for prevention of fogging. 2 En 3 CAUTION: · The silica gel bag will be caught when the Case is sealed and water leakage will occur. · Once silica gel has been used, the moisture absorption performance will be impaired. Always replace the silica gel when the Case is opened and closed. Make sure the camera is loaded properly Check the following points before sealing the Case. · Is the digital camera loaded properly?· Is silica gel inserted all the way at the specified location? [. . . ] Also remove any sand or dirt adhered to the O-ring contact surface on the front lid of the case. En CAUTION: · Maintenance of the waterproof functions is required even before using this product underwater for the first time. · When a sharp object is used to remove the O-ring or to clean the inside of the O-ring groove, the Case and the O-ring may be damaged and water leakage may occur. · Take care not to stretch the O-ring. · Never use alcohol, thinner, benzene or similar solvents or chemical detergents to clean the O-ring. [. . . ]