User manual OLYMPUS PT-E06

[. . . ] PT-E06 Jp En Fr De Sp Cs Kr Instruction Manual Underwater Case for digital camera Mode d'emploi Caisson étanche pour l'appareil photo numérique Bedienungsanleitung Unterwassergehäuse für Digitalkamera Manual de instrucciones Caja estanca para la cámara digital Thank you for buying the Underwater Case PT-E06 (hereinafter Case). Please read this instruction manual carefully and use the product safely and correctly. Please keep this instruction manual for reference after reading it. Wrong usage may cause damage to the camera inside the Case due to water leakage, and repair may not be possible. [. . . ] Refer to the UFL-2 instruction manual for the UFL-2 operation. CAUTION: En When using a non-Olympus manufacturer's slave-type flash with underwater optical fiber cable, set the camera's built-in flash to manual. If the camera's built-in flash ratio is more than 1/64, the camera's built-in flash light may reflect in the lens port and be taken into the picture. EN 11 When using the TTL cable When connecting the optional electronic flash with the underwater TTL cable (optional: PTCB-E01), connect the hot shoe cable (optional: PHCB-01) to the camera and front cover of the Case. Connecting the underwater TTL cable 1 Turn the TTL connector cap of the Case counterclockwise and remove it. 2 Connect the underwater TTL cable (optional: PTCB-E01) to the TTL connector on the Case. Insert into the connector. Underwater TTL cable Use this mark to align the position. 3 When not using the underwater TTL cable, attach the TTL connector cap. Make sure there is no foreign matter attached to the O-rings inside the cap and on the TTL cable connector. After that, gently turn it clockwise until it stops. Check O-rings Turn the threaded section of the connector clockwise gently until it stops. Cap Connector CAUTION: If the TTL connector cap is loose, water leakage may result. How to connect the hot shoe cable 1 Turn the hot shoe cable connector cap inside the Case counter-clockwise to remove it. 2 Insert the connector of the hot shoe cable into the Case's connector and turn the connector screws all the way clockwise to connect them firmly. 3 Load the camera in the Case, and then connect the hot shoe cable to the camera. En EN 12 Setting of the digital camera 1 Set the automatic pop-up setting of the camera to OFF. The camera's built-in flash is designed to pop up automatically when shooting under low light or against the sun in any scene mode other than the AUTO or underwater modes. For details on camera function setup, refer to the camera's instruction manual. 2 Switch the electronic flash ON before switching the camera ON. When using the electronic flash, be sure to turn it ON before turning the camera on. If the automatic pop-up setting of the camera is ON and the camera is set to the scene mode other than the AUTO or underwater modes, turning the camera ON before turning the electronic flash on would cause the camera's built-in flash to pop up automatically. Always be sure to turn the electronic flash ON before turning the camera ON. CAUTION: · If the camera's built-in flash pops up while the hot shoe cable is connected to the camera, it will interfere with the hot shoe cable, either disconnecting it or causing a connection failure. · When using a slave-type underwater flash from a non-Olympus manufacturer, pop the camera's built-in flash up before loading it in the Case. · Once the Case has been sealed, the built-in flash cannot be popped up or stored. En EN 13 4. Installing the digital camera Check the digital camera Check the digital camera before loading it in the Case. 1. Battery Confirmation Underwater shooting can reduce battery life because the picture has to be checked on the LCD monitor before and after shooting. Make sure that you have sufficient remaining battery capacity before use. 2. Check the remaining number of pictures Check that the image storage medium has enough room for the number of pictures you want to take. 3. [. . . ] Use the maintenance adapter to remove the O-ring unit from the TTL connector cap. TTL connector cap Maintenance adapter En 1 Insert the adapter by aligning its pin with the hole on the cap. 2 Turn the adapter counterclockwise to remove the Oring unit. 3 After removing the O-ring attached to the O-ring unit, clean the O-ring groove and apply silicone grease to the O-ring. Then, re-attach the O-ring to the O-ring unit. * Reverse the removal procedure to re-attach the O-ring unit to the TTL connector cap. O-ring EN 24 7. Appendix Specifications Available models Pressure resistance Main materials Olympus Digital Camera E-620 Depth of down to 40 m (130 feet) Main body: Polycarbonate resin. [. . . ]