User manual OMNIMOUNT CLSP INSTALL

[. . . ] If OmniMount products are used for purposes other than their original intent, OmniMount, its distributors and retailers shall not be held responsible or liable for injuries or property damage, direct, indirect, or consequential, which may arise from the inability to use this product safely, properly, and in the manner for which it has been designed and manufactured. Warranty does not apply to products which have been lost, damaged by misuse, abuse, or accident. OmniMount Systems, Inc. 8201 South 48th Street · Phoenix, AZ 85044-5355 1-800-MOUNT-IT · www. omnimount. com Designed for Flat Panel TV's up to 24" Maximum Weight Capacity: 30 lbs. (13. 6 Kg) VESA compliant: VESA 75/100 Installation Template Included Integrated Cable Management Lift N' Lock Installation Questions? [. . . ] Note: Cable Covers and Retaining Screws do not need to be removed from flat side to install cables. Fig. 9 Step 3 -- Mounting to the Wall 9. 1 Follow the instructions based upon your mounting surface: 3a Wooden Stud 3b Concrete/Masonry 3c Cinder Block Fig. 2 To simplify the cable installation process, route the cables through one arm section, and then re-attach the cable covers before proceeding to the next arm section. Step 3a -- Mounting to Wooden Studs The CL-S can be mounted on a single wooden stud. Using an electronic stud finder (Fig 2), locate the center of the wooden stud at the desired mounting location. Mark the stud center position directly onto the wall. Extend the stud center line, and then draw a horizontal line where you wish the center of the screen to be located. Measure and mark the center position of this horizontal line. Insert supplied thumbtack into center mark on template. Remove the tape strip from the back of the guide. Remove the four square perforations above center hole to help align the template with the center mark of the stud. Using a bubble level, level the guide, and then press the adhesive backing against the wall to hold the guide in place. Using a 1/8" (3mm) drill bit, drill 2 pilot holes 1. 5" (40 mm) deep into the center of the studs, through the circular cut-out sections of the installation template. Note: For best results from the dust channel, press and hold the template against the wall about 2" (50 mm) from where you are drilling. Carefully remove the guide from the wall, and discard. Note: Be sure to hold the guide in an upright position so as not to spill the collected dust. Note: To reduce signal interference OmniMount recommends that the power cable be installed on the lower arm and A/V cables be installed on the upper arm. If an RF cable needs to be installed, installation on the lower arm is recommended. To install the A/C Power Cable (10. 1), run the wire through the Lower Arm's recessed cable channel (10. 2) and then attach it directly to the display. You may also run a mini RF Cable (10. 3) in the same fashion. DO NOT run these through the Front Arm (10. 4). To install other A/V cables, route the cables into the Recessed Section of the Upper Arm (10. 5). Then, route the cables around (10. 6) to the recessed section on the opposite side of the Front Arm (10. 4). Note: Be sure to leave some slack in the cable so that the arm assembly can move freely without stretching or damaging the cables. Step 3b -- Mounting to Concrete/Masonry Fig. 10 10. 6 The CL-S can be mounted directly to concrete/masonry walls. Fig. 3 WARNING · · NEVER drill into mortar joints! [. . . ] Carefully remove the guide from the wall, and discard. Note: Be sure to hold the guide in an upright position so as not to spill the collected dust. Insert wall anchors into the mounting holes, and lightly tap them flush to the wall with a hammer. (Fig 3) VESA 100 VESA 75 The Mounting Head of the CL-S is VESA compliant, and supports the following VESA Patterns (Fig. [. . . ]