User manual OMRON CX-DESIGNER INTRODUCTION GUIDE

[. . . ] General Precautions The user must operate each product according to the performance specifications described in the operation manuals. Before using the product under conditions which are not described in the manual or applying the product to nuclear control systems, railroad systems, aviation systems, vehicles, combustion systems, medical equipment, amusement machines, safety equipment, and other systems, machines and equipment that may have a serious influence on lives and property if used improperly, consult your OMRON representative. Make sure that the ratings and performance characteristic of the product are sufficient for the systems, machines, and equipment, and be sure to provide the systems, machines, and equipment with double safety mechanisms. This manual provides information for using the programmable terminal model NS12. [. . . ] "6" Repeat direction Set "1" to [Offset Address] Click Start up CX-D Creating a new project Project property System setting Creating a screen Validation Transferring a project Create a label as shown on the right by referring to "9. Uncheck it. Create labels for "Alarms 8 to 12" in the way you created "Alarms 1 to 6". Click any area on the screen except frame objects to finish "Edit Inside Group/Frame. Start up CX-D Creating a new project Project property System setting Creating a screen Validation Transferring a project 15. Numeral Display & Input Numeral Display & Input is an object that displays data of an address as numeral value and changes data by inputting numeral value from a virtual key board. Touch the object on the screen. Touch the object on the screen. Ten key pad appears. The user can enter values The user can enter values to the specified area. to the specified area. Create labels as shown on the right by referring to "9. "Present Value" Lower [Label] !"Set Value". Start up CX-D Creating a new project Project property System setting Creating a screen Validation Transferring a project Select the Numeral Display& Input icon and place it next to the label "Present Value". Set as follow from the object property list. Check the box. General tab [Address] !"HOST 1 DM00100" [Display Format] !"INT (Signed 1 word)" [Integer] !"0" Select the Numeral Display & Input icon from the object list Set as follow from the object property list. "White" Start up CX-D Creating a new project Project property System setting Creating a screen Validation Transferring a project 16. Word button is an object that writes constants to the address (DM etc. . . ) when it is pressed, or increases/decreases the value of the address. It is possible to display a pop-up menu and select the value from constants. In this manual, you will create a word button to write the set value (Internal address) to the present value (PLC address). Paste a Word button. Set as follow on the object property list. General tab [Address] !"$W0" Also set [Color 1] and [Color 3]. Text tab [Label] !"Transfer" Start up CX-D Creating a new project Project property System setting Creating a screen Validation Transferring a project Create three labels by referring to "9. "Numeral Value Input & Display" [Label] !"Word Button" Start up CX-D Creating a new project Project property System setting Creating a screen Validation Transferring a project Creating Third Screen Create three labels by referring to "13. Add a Screen". Click A new screen is created. 17. [. . . ] You can also check that the address of the Alarm 1 is turned ON on the Test Tool dialog. Click the Close button. Click the Screen 3 button. Start up CX-D Creating a new project Project property System setting Creating a screen Validation Transferring a project [Confirming a movement of Alarm/Event. ] You can check the alarm that was occurred on the previous page. Click the Switch Label button. [Check a movement of the Switch Label button. ] Click [Dutch] in the menu. Click the [X] button to end the Test tool. Start up CX-D Creating a new project Project property System setting Creating a screen Validation Transferring a project Transferring project data Transferring project data Transferring projects created on CX-Designer to the NS hardware. There are six ways to transfer a project: serial cable, Modem, Ethernet, Controller link, USB and Memory card. In this manual, you will transfers project data via serial cable and using a memory card. [. . . ]