User manual OMRON CX-INTEGRATOR V1.1

[. . . ] 1. 1 Operation Manual Revised November 2005 iv Notice: OMRON products are manufactured for use according to proper procedures by a qualified operator and only for the purposes described in this manual. The following conventions are used to indicate and classify precautions in this manual. Always heed the information provided with them. Failure to heed precautions can result in injury to people or damage to property. !DANGER Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. [. . . ] Beginning with the start addresses, nodes 01, 02, and 03 are set in order. (Reception from node 01 is first, followed by transmission from the local node, and finally reception from node 03. ) Sets CIO 1300 as the data link status start address. Area 2 Ordered destination nodes Data link status start address Memory area Start address CIO 1300 9 Set node address 03 as shown in the following table, and then click the Next Button or press the Enter key. Item Node address PLC type Area 1 Memory area Start address Send size Memory area Start address Send size Data set 3 CS1GCPU45 IR 300 40 DM 700 40 2, 1, 3 Description - - Sets IR 300 as the data link start address for the Area 1 local node. Sets 40 words as the send size (unit: words) for the Area 1 local node. Sets DM 700 as the data link start address for the Area 2 local node. Sets 40 words as the send size (unit: words) for the Area 2 local node. Beginning with the start addresses, nodes 02, 01, and 03 are set in order. (Reception from node 02 is first, followed by reception from node 01, and finally transmission from the local node address. ) Sets LR0 as the data link status start address. Area 2 Ordered destination nodes Data link status start address Memory area Start address LR 0 4-15 4-3 4-3-4 Manually Setting Data Links Creating Data Link Tables Offline Note Fast Datalink Wizard Settings It is possible to generate a table with all nodes set for the same PLC type and the same areas (using Fast Default Table Generation), and then to modify individual nodes in the Node Editing Window as required. Make the settings as follows: 1 Click the Defaults Button and then set the default values in the following dialog box. 2 Select the Fast Default Table Generation Option, and then click the Next Button or press the Enter key. The settings for all participating nodes will be generated at the above default values. · PLC type · Memory area, data link start address, communications data size · Status memory area 4-16 4-3 4-3-4 Manually Setting Data Links Creating Data Link Tables Offline Node Editing Window Settings 10 The following Datalink Component Window will be displayed. Data Link Configuration window Node Editing window Data Link Configuration Window Indicates the data link memory area. 1: Area 1 2: Area 2 The ovals indicate the send areas (Area 1 and Area 2). The rectangles indicate the receive areas (Area 1 and Area 2). The same color indicates that data is shared among nodes. Participating data link node address : The arrows indicate the direction of data transfer. Send areas are indicated by ovals in order of the addresses of nodes participating in the data links. The same color indicates that data is shared among nodes. Therefore, with the number of participating nodes represented by n, one oval and n-1 rectangles are shown for each node. This window can be used to check the data sent and received between nodes. 4-17 4-3 4-3-4 Manually Setting Data Links Creating Data Link Tables Offline Node Editing Window Settings Set the data link details for each node (i. e. , send size, receive size, reception offset) in the Node Editing Window. Note: The Node Edit Window appears in table format by default, as shown below. To convert it back into the earlier list format, select View - Show in List. (1) (2) (5) (6) (7) (8) (9) The settings for each active node shown in the node field to the left are displayed here. (3) No. (1) (2) (3) (4) (5) Name Node PLC Status Area 1/Area 2 Node (Display only. (Automatic display) Size (Setting/Display) (4) (10) Description Selects the address of the node to be edited. The settings for an active node (selected with The PLC type set by the Datalink Wizard is displayed and can be changed here. The status memory area and start address set by the Datalink Wizard are displayed and can be changed here. The Area 1 and Area 2 classifications and start addresses set by the Datalink Wizard are displayed and can be changed here. [. . . ] Pages 2-11 to 2-13: Information added on connecting online. Pages 2-19, 20: Information added on setting the IP address table. Pages 2-23 to 2-25: Information added on uploading network configurations. Pages 2-38 to 2-40: Information changed on uploading and downloading component parameters. [. . . ]