User manual OMRON CX-PROGRAMMER INTRODUCTION GUIDE

[. . . ] Introduction - Please be sure to read and understand Precautions and Introductions in CX-Programmer Operation Manual before using the product. - This Guide describes the basic operation procedure of CX-Programmer. Refer to the Help or the Operation Manual of the PDF file for detailed descriptions. - Acrobat Reader 5. 0 or later is required to read the PDF files. [. . . ] Edit of Symbol Comment Click Ladder Window is switched to the Symbol Comment Editing window. Double-click the left mouse button on a bit number that you want to enter a symbol comment, and you will able to enter a symbol comment. Copy&Paste and deletion of one or more comments are possible by the cell. Copy&Paste and deletion of one or more comments are possible by the cell. Drag the mouse with the right mouse button pressed to invert the source bits of copy in blue. Click the right mouse button on the range, and select [Copy] from the popup menu. Copy&Paste of symbol Copy&Paste of symbol comments is possible between comments is possible between Excel and CX-Programmer too. Example of copying & pasting comments of two bits Click the right mouse button on the bit number of the copy destination, and select [Paste]. The comments of the selected two bits are copied. Installation Installation to Startup to Startup Opening a Opening a new project new project Device type Device type settings settings Creating a Creating a program program 5-4. Entry of Rung Comment Move the cursor to this position. (The rung is inverted in blue. ) ENT The entry screen shows up. [Process_at_Startup] Enter a rung comment. ENT 5-5. Entry of Normally Closed Contact / Press "/" from a keyboard to show the [New Closed Contact] dialog. 1 ENT Sensor 1 ENT Installation Installation to Startup to Startup Opening a Opening a new project new project Device type Device type settings settings Creating a Creating a program program O ENT 101 Coil 1 ENT R 5-6. Entry of Attached Comments This function is very useful for keeping change histories at maintenance and notes of debug bits at startup. Move the cursor to the contact to which you want to write an annotation. Alt ENT The entry screen shows up. Or click the right mouse button. 2002 Added by Tanaka, Maintenance Dept. ]. ENT Press [Alt] + [A] to switch showing/hiding of attached comments. Installation Installation to Startup to Startup Opening a Opening a new project new project Device type Device type settings settings Creating a Creating a program program 5-7. Entry of Differential Contact. . . Up C 100 Click Click [Up]. ENT This entry method is available only for CS/CJ and CV series PLCs. For the other series PLCs, use DIFU (13). ENT C 5-8. Entry of Differential Contact. . . Down 101 Click Click [Down]. This entry method is available only for CS/CJ and CV series PLCs. For the other series PLCs, use DIFD (14). ENT Installation Installation to Startup to Startup Opening a Opening a new project new project Device type Device type settings settings Creating a Creating a program program 5-9. Entry of Vertical. . . Up Ctrl Or U O ENT 200 Coil 2 ENT R C ENT O ENT 200 ENT 300 Coil 3 ENT 5-10. Entry of Vertical. . . Down Ctrl Or V Installation Installation to Startup to Startup Opening a Opening a new project new project Device type Device type settings settings Creating a Creating a program program 5-11. Entry of Advanced Instructions 1 - Entry of Strings I Show the [New Instruction] dialog. Enter an instruction and its operand. ++ d0 ENT See the next page for the contents of instructions. Enter a comment. Products ENT R Installation Installation to Startup to Startup Opening a Opening a new project new project Device type Device type settings settings Creating a Creating a program program 5-12. [. . . ] As well as the operations so far, move the cursor to the contact 1. 01 and press the [Space] key. Space (6)The focus moves to the coil 1. 01. As it turned out, the cause was the contact 0. 01 that was not turned on. Press the [Space] key to jump from a coil to a contact having the same address as the coil or from a contact to a coil in reverse. Press the [N] key for another jump from a contact or coil at the cursor position to a next one having the same address. [. . . ]