User manual OMRON CXONE-ALD-V4 10-2010

[. . . ] W418-E1-07 SYSMAC CXONE-AL_C-V4/ CXONE-AL_D-V4 Face Plate Auto-Builder for NS (Ver. D-V4 Face Plate Auto-Builder for NS (Ver. 3. 1) Operation Manual Revised October 2010 iv Notice: OMRON products are manufactured for use according to proper procedures by a qualified operator and only for the purposes described in this manual. The following conventions are used to indicate and classify precautions in this manual. [. . . ] The status character string displayed is determined according to the value of tag ITEM PV_ABN. Display (No characters displayed. ) PV error indication PV_ABN (ITEM 019) 0 1 This field is created as an ON/OFF Button using a Select Shape of type 1 and switches to display PV error indication characters. 4: Alarm Status Display MH and ML are not provided with 3-position ON/OFF. The other settings are the same as for Basic PID. The following diagram shows a face plate for 3-position ON/OFF built with the Face Plate Auto-Builder for NS in a 640×480 screen resolution. The whole face is built using 458×142 dots. 53 Three-position ON/OFF (Block Model 002) Section 6-4 The display and operation of each object in the face plate is the same as the version for 800×600 screen resolution. 6-4-2 Tuning Screens The Tuning Screens for 3-position ON/OFF are almost the same as for Basic PID (Block Model 011), except for the following differences. A setting field for each parameter is not provided. MV is not included in the realtime trend graph. MV is not included in the realtime trend graph. 4. The face plate is for 3-position ON/OFF. The following screen is a Tuning Screen for 3-position ON/OFF built using the Face Plate Auto-Builder for NS in a 640×480 screen resolution. 54 Indication and Operation (Block Model 032) Section 6-5 The display and operation of each object in the face plate is the same as the version for 800×600 screen resolution. A setting field for each parameter is not provided, so up to eight characters can be displayed for the unit character string for 3-position ON/OFF, instead of the four characters for Basic PID. 6-5 Indication and Operation (Block Model 032) This section describes only the differences between the Indication and Setting and Basic PID (Block Model 011). For details on the areas not covered here, refer to 6-1 Basic PID (Block Model 011). 6-5-1 Face Plates The face plates are almost the same as for Basic PID (Block Model 011), except for the following aspects. · The SP is X1 (Auto input) and read-only (no SP Change Button provided). · A deviation alarm (DV) is not provided. · Remote mode is not supported. 55 Indication and Operation (Block Model 032) Section 6-5 1 2 3 5 4 The actual graphic display is shown below. 1: Status Display Either AUTO or MAN is displayed. CAS (Remote and Auto) mode is not supported, which is different from Basic PID. The status character string displayed is determined by the value of tag ITEM A/M_SW. (R/L_SW is not referenced, which is different from Basic PID. ) Display MAN AUTO 0 1 A/M_SW (ITEM 086) This field is created as an ON/OFF Button using a Select Shape of type 2 and switches to display AUTO/MAN characters. 2: Alarm Status Display Indication and Setting does not provide a deviation alarm, so there is no display. 3: Auto Input The fixed characters "X1" are displayed as a Text object. The numeral display field is display-only. (A Control Flag is set to disable input. ) The numeral display for X1 uses an engineering unit. 4: Switch to AUTO Button This button switches operation to Auto mode and is displayed in red during Auto mode. [. . . ] The backup during operation function backs up the function blocks in the RAM in the Loop Control Board to the flash memory in the Loop Control Board. 4: GRF and PRG Buttons GRF Button: Opens the Step Data Graph Display Screen. PRG Button: Opens the Step Data Setting Screen. 5: Bank Display Switching Buttons Up to 5 banks can be displayed on each Bank Data Setting Screen. [. . . ]