Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual OMRON D4MC. We hope that this OMRON D4MC user guide will be useful to you.
Lastmanuals help download the user guide OMRON D4MC.
Detailed instructions for use are in the User's Guide.
[. . . ] Inductive loads have a power factor of 0. 4 min. Lamp load has an inrush current of 10 times the steady-state current. Motor load has an inrush current of 6 times the steady-state current. [. . . ] × 5 (see note 1) M12 x 1 mounting screw Two hexagon nuts (thickness: 3 width: 17)
16 dia.
(See note 2)
Note:
1. The length of the imperfect threads is 1. 5 mm maximum.
22 max.
15 Terminal protective cover Two, 4. 3±0. 1 dia. mounting holes
(21 x 21)
Seal rubber (NBR)
4
D4MC
Panel Mount Crossroller Plunger D4MC-5040
M12 x 1 mounting screw Two hexagon nuts (thickness: 3 width: 17)
(See note 2) 16 dia.
D4MC
12. 7 dia. The length of the imperfect threads is 1. 5 mm maximum.
22 max. (21 x 21)
Terminal protective cover
Two, 4. 3±0. 1 dia. mounting holes
Seal rubber (NBR)
Short Hinge Lever D4MC-1020
t = 1 (see note)
Note:
Stainless steel lever
22 max.
15
(21 x 21)
Terminal protective cover
Two, 4. 3±0. 1 dia. mounting holes
Seal rubber (NBR)
Hinge Lever D4MC-1000
t = 1 (see note)
22 max. 15 (21 x 21)
Note: Seal rubber (NBR)
Stainless steel lever
Terminal protective cover
Two, 4. 3±0. 1 dia. mounting holes
Hinge Roller Lever D4MC-2000
t=1 (see note 1)
12. 7 dia. Plastic roller
Terminal protective cover
Two, 4. 3±0. 1 dia. mounting holes
Seal rubber (NBR)
Short Hinge Roller Lever D4MC-2020
t=1 (see note 1)
12. 7 dia. × 7. 5 (see note 2)
Note:
22 max. Plastic roller
Terminal protective cover
Two, 4. 3±0. 1 dia. mounting holes
Seal rubber (NBR)
5
D4MC
One-way Action Short Hinge Roller Lever D4MC-3030
t=1 (see note 1)
Angle of roller swing: 90°
D4MC
14
12. 7 dia. 15
(21 x 21)
Terminal protective cover
Two, 4. 3±0. 1 dia. mounting holes
Seal rubber (NBR)
Mounting Holes
Two 4. 3 dia. mounting holes or M4 screw holes
25. 4 ± 0. 15
Molded Terminal Models
Molded Terminal Models
The molded terminal model is available with right-hand, left-hand and underside leads and is recommended for use where the Switch is exposed to dust, oil, or moisture. When placing your order for the Switch specify the required length of V. C. T. [. . . ] Screwdriver
· ·
When mounting the Panel Mount-type Switch (DCMC-5000, D4MC5020, or D4MC5040) with screws on a side surface, remove the hexagonal nuts from the actuator. When mounting the panel mount type on a panel, be careful not to tighten to an excessive torque. Tightening the screws to a torque exceeding 4. 91 N S m will cause the plunger to fail.
Mounting Hole Dimensions D4MC-5000
12. 5 +0. 2 0 dia.
D4MC-5020, D4MC5040
12. 5 +0. 2 dia. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE OMRON D4MC
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual OMRON D4MC will begin.
