User manual OMRON D5A DATASHEET

[. . . ] Limit type: 50 x 10 Operating: ­20C to 75C (with no icing) Operating: 30% to 85% (30% to 95% with the seal rubber) 10 mm max. 20 mm max. Degree of protection Repeat accuracy (see note 2) Life expectancy (see note 3) Deviation in electrical life expectancy after 1, 000, 000 operations Operating speed Rated frequency Insulation resistance Contact resistance Dielectric strength Vibration resistance Shock resistance Temperature coefficient (see note 4) Ambient temperature Ambient humidity Note: 1. Contact your OMRON sales representative for measurement conditions of the repeat accuracy. Life expectancy values are calculated at an operating temperature of 5C to 35C, and an operating humidity of 40% to 70%. [. . . ] Seal rubber Ceramic plunger 0. 8 2. 5 M8 × 0. 5 (see note) S-FLEX V-HKCVV equal level, 3 dia. Two cores 0. 08 mm2 1M 3 dia. 15 dia. 21. 5 Operation indicator fiber, 2 dia. 450 mm) Two clamping nuts Note: The threads of the case are not standard. Therefore, standard tapping to the case is not possible for mounting. Toothed lock washer M8 Type (Contact Output) D5A-3200, D5A-3300 13 4. 85R 2 dia. 0. 8 OP (FP) 2. 5 S-FLEX V-HKCVV equal level, 3 dia. Seal rubber 16. 5 Two clamping nuts M8 × 0. 5 (see note) Note: The threads of the case are not standard. Therefore, standard tapping to the case is not possible for mounting. 15 dia. Ceramic plunger Toothed lock washer Slim Type (Solid-state Output) D5A-5210, D5A-5310 8 Operation indicator (LED) Seal rubber Ceramic plunger 4 12 5 2 dia. OP (FP) S-FLEX V-HKCVV equal level, 3 dia. Two cores 0. 08 mm2 1M 3 dia. 4. 85R 4 12±0. 2 20 Two, 2. 7+0. 1 dia. -0 275 D5A M16 Type (Contact Output/Solid-state Output) D5A-7400, D5A-7410 24 1/8-inch ultrahard ball D5A 1. 2 4 M16 × 0. 5 (Length: 28. 5) (see note) Nameplate Operation indicator (LED) (see note) 3 dia. Two cores 0. 08 mm2 1M Note: Not available in the contact output type. 8 dia. 26 dia. PT OP 37. 5 45 Toothed lock washer M16 Type (Contact Output/Solid-state Output) D5A-7403, D5A-7413 (Connector type) Two clamping nuts Note: The dimensions are the same as the above model's. 20 Limit Type (Solid-state Output) D5A-8511, D5A-8512 Two, M3 × 0. 5 20±0. 2 30 20±0. 2 15 dia. Two, 4. 2 dia. spot facing depth: 5 PT 3 OP 6 Nameplate Operation indicator (LED) 3 dia. 20 8 dia. 5 16 10 37. 5 45 S-FLEX V-HKCVV equal level, 3 dia. Two cores 0. 08 mm2 3M/5M Limit Type (Solid-state Output) D5A-8514, D5A-8515 (Connector type) 20 Note: The dimensions are the same as the above model's. Limit Type (Solid-state Output) D5A-9511, D5A-9512 Two, M3 × 0. 5 PT 3 OP 6 Two, 4. 2 dia. spot facing depth: 5 Operation indicator (LED) Nameplate 30 20±0. 2 20 ±0. 2 15 dia. 8 dia. 3 20 dia. Two cores 0. 08 mm2 3M/5M 16 5 10 37. 5 45 Limit Type (Solid-state Output) D5A-9514, D5A-9515 (Connector type) 20 Note: The dimensions are the same as the above model's. 276 D5A D5A Precautions I Correct Use Do not impose compressing loads on the fiber cable. Fiber cable Handling of Fiber Cable Do not pull or impose any force exceeding 29. 42 N on the fiber cable. Make sure that the bending radius of the fiber cable is as large as possible and at least 25 mm. The 40-mm portion of the fiber cable on the connector end as shown below must not be bent. 40 mm min. R25 mm min. The fiber cable can be cut with OMRON's E39-F4 Cutting Tool. Do not impose any force exceeding 29. 42 N on the cord, otherwise the cord may break. Make sure that the bending radius of the cord is at least 20 mm. Mounting For the mounting dimensions, refer to the following figures and tables. Dimensions B M5 Contact output M8 Solid-state output M16 A B C C A Mounting hole Panel thickness Toothed lock washer Dimensions 5. 20. 1 mm dia. [. . . ] In the above circuit, suppose the MY relay rated at 12 VDC is used as the load. Since the must operate voltage of the relay is 80% or less than the rated voltage, it is 12 x 0. 8 = 9. 6 V. The hardness (Hv) of a bevel plunger is 2, 000 or over, for which it is recommended that a dog that has an Hv value of 1, 000 or less be used. Do not fail to provide a stopper so as to prevent the enclosure of the D5A from being used as the stoppers. D5A Exercise care that excessive force is not applied to the ceramic plunger of M5, M8, or slim type. [. . . ]