User manual OMRON DZ DATASHEET

[. . . ] Actuator None: Pin plunger V: Hinge lever V22: Short hinge roller lever V2: Hinge roller lever W: Hinge lever W22: Short hinge roller lever W2: Hinge roller lever 4. Terminals A: Solder terminal B: Screw terminal Ordering Information List of Models Actuator OT 0. 13 mm min. Solder terminal DZ-10G-1A DZ-10GW-1A DZ-10GV-1A DZ-10GW22-1A DZ-10GV22-1A DZ-10GW2-1A DZ-10GV2-1A Screw terminal DZ-10G-1B DZ-10GW-1B DZ-10GV-1B DZ-10GW22-1B DZ-10GV22-1B DZ-10GW2-1B DZ-10GV2-1B Pin plunger Hinge lever Short hinge roller lever Hinge roller lever 1. 2 mm min. 0. 26 mm min. Special-purpose Basic Switch DZ F-139 Limit Switches Model Number Structure Specifications Approved Standards Agency UL CSA UL508 CSA C22. 2 No. [. . . ] The solder terminal model has a suffix "-1A" in its model number and its omitted dimensions are the same as the corresponding dimensions of the pin plunger model. Limit Switches Pin Plunger DZ-10G-1B PT 23. 3±0. 25 2. 5SR (stainless-steel pin plunger) 3 dia. 0. 4 OP 4. 2+0. 075 -0. 025 4. 36+0. 1 dia. -0. 05 11. 9 25. 4±0. 1 49. 2 4. 2+0. 075 dia. hole -0. 025 17. 45±0. 2 14. 5 8. 2 OF max. OP 5. 59 N {570 gf} 0. 55 N {57 gf} 1. 7 mm 0. 13 mm 0. 4 mm 15. 6±0. 4 mm Hinge Lever DZ-10GW-1B 28. 4 63. 5R t = 1 (stainless-steel lever) 4. 9 FP 19. 7 17. 7 +0. 075 OF max. OP * 1. 67 N {170 gf} 0. 27 N {28 gf} 1. 6 mm 4 mm 46. 3 mm 21. 8±1 mm 14. 5 OP 8. 2 11. 9 25. 4±0. 1 49. 2 4. 2+0. 075 dia. hole -0. 025 17. 45±0. 2 4. 2 -0. 025 4. 36 -0. 05 dia. +0. 1 DZ-10GV-1B PT 63. 5R t = 1 (stainless-steel lever) 1. 1 4. 9 OP 14. 5 4. 2 -0. 025 +0. 075 17. 7 19. 7 8. 2 +0. 075 11. 9 4. 2 -0. 025 dia. OP 1. 96 N {200 gf} 0. 13 N {14 gf} 6 mm 0. 4 mm 1. 7 mm 18. 3±1 mm 4. 36 -0. 05 dia. +0. 1 25. 4±0. 1 49. 2 17. 45±0. 2 Special-purpose Basic Switch DZ F-141 Short Hinge Roller Lever DZ-10GW22-1B t = 1 (stainless-steel lever) 28. 4 26. 2R OP 19. 7 17. 7 4. 2+0. 075 -0. 025 11. 9 4. 36+0. 1 dia. OP 3. 92 N {400 gf} 0. 83 N {85 gf} 0. 9 mm 2. 4 mm 39. 7 mm 30. 2±0. 8 mm FP 14. 5 8. 2 4. 2+0. 075 dia. hole -0. 025 17. 45±0. 2 25. 4±0. 1 49. 2 DZ-10GV22-1B PT t = 1 (Stainless-steel lever) 9. 5 dia. × 4 (plastic roller) 30. 2R 1. 1 OP 14. 5 4. 2+0. 075 -0. 025 +0. 075 +0. 1 4. 36-0. 05 dia. OF max. OP 4. 22 N {430 gf} 0. 41 N {42 gf} 3 mm 0. 13 mm 0. 6 mm 29. 4±0. 8 mm 17. 7 19. 7 8. 2 25. 4±0. 1 49. 2 11. 9 4. 2 -0. 025 dia. hole 17. 45±0. 2 Hinge Roller Lever DZ-10GW2-1B t = 1 (stainless-steel lever) 28. 4 48. 4R FP OP 19. 7 17. 7 4. 2+0. 075 -0. 025 4. 36-0. 05 dia. +0. 1 9. 5 dia. OP 2. 09 N {213 gf} 0. 41 N {42 gf} 1. 2 mm 3. 3 mm 47. 6 mm 31. 8±0. 8 mm 14. 5 8. 2 25. 4±0. 1 49. 2 11. 9 4. 2+0. 075 dia. hole -0. 025 17. 45±0. 2 DZ-10GV2-1B PT t = 1 (stainless-steel lever) 9. 5 dia. × 4 (plastic roller) 48. 4R OP 14. 5 4. 2+0. 075 -0. 025 4. 36+0. 1 dia. -0. 05 17. 7 19. 7 8. 2 17. 45±0. 2 1. 1 OF max. OP 2. 65 N {270 gf} 0. 33 N {34 gf} 4 mm 0. 26 mm 1. 1 mm 29. 4±0. 8 mm 4. 2+0. 075 dia. hole -0. 025 25. 4±0. 1 11. 9 49. 2 F-142 Special-purpose Basic Switch DZ Terminals Solder Terminals (-1A) Screw Terminals (-1B) Six M3 pan head screws (with toothed washer) Precautions Refer to the Technical Information for Basic Switches (Cat. [. . . ] In order to determine the life of a Switch model to be applied to a particular use, it is best to conduct an appropriate durability test on some samples of the model under actual conditions. Make sure that the actuator travel does not exceed the permissible OT position. The operating stroke must be set to 70% to 100% of the rated OT. 25. 4 ± 0. 1 Accessories (Order separately) Refer to Z/A/X/DZ Common Accessories for details about Terminal Covers, Separators, and Actuators. Special-purpose Basic Switch DZ F-143 ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0. 03937. [. . . ]