User manual OMRON E2EQ DATASHEET

[. . . ] of sensing distance at 23°C within temperature range of -40°C to 85°C ±10% max. of sensing distance at 23°C within temperature range of -25°C to70°C ±1% max. of Sensing distance in rated voltage range ±15%. [. . . ] Operation indicator (red), operation setting indicator (green) Operating/Storage: 35% to 95%RH (with no condensation) 50 M min. (at 500 VDC) between energized parts and case 1, 000 VAC for 1 min between energized parts and case 10 to 55 Hz, 1. 5 mm double amplitude for 2 hours each in X, Y, and Z directions IEC60529 IP67 Teflon resin coating (base: brass) * Teflon resin * Instruction manual * Teflon is a registered trademark of Dupont Company and Mitsui Dupont Chemical Company for their fluoride resin. E2EQ D-173 Characteristic data (typical) Sensing Distance vs. Sensing Object E2EQ-X4X1(-M1J) Sensing distance X (mm) 5 E2EQ-X8X1(-M1J) Sensing distance X (mm) 10 E2EQ-X15X1(-M1J) Sensing distance X (mm) 20 #d X #d X t=1mm Mild steel t=1mm Mild steel #d X t=1mm Mild steel 4 Stainless steel (SUS304) 3 Brass 2 Copper 1 8 16 6 Stainless steel (SUS304) 4 12 Stainless steel (SUS304) 8 Brass Aluminum 4 Copper Brass Copper 2 0 5 10 15 20 25 30 35 0 10 20 30 40 50 0 10 20 30 40 50 60 70 80 Side length of sensing object d (mm) Side length of sensing object d (mm) Side length of sensing object d (mm) E2EQ-X3D1(-M1GJ) Sensing distance X (mm) 4. 0 3. 5 3. 0 2. 5 2. 0 Aluminum 1. 5 1. 0 0. 5 Brass E2EQ-X7D1(-M1GJ) Sensing distance X (mm) 10 9 8 Mild steel 7 6 5 4 Brass 3 Copper 2 1 Aluminum Copper Stainless steel (SUS304) E2EQ-X10D1(-M1GJ) Sensing distance X (mm) 14 #d X t=1mm Mild steel Stainless steel (SUS304) #d X t=1mm #d 12 10 8 6 X t=1mm Mild steel Stainless steel (SUS304) Brass 4 2 Aluminum Copper 0 5 10 15 20 25 30 35 Side length of sensing object d (mm) 0 5 10 15 20 25 30 35 40 45 Side length of sensing object d (mm) 0 5 10 15 20 25 30 35 40 45 50 55 Side length of sensing object d (mm) D-174 Inductive Sensors Output Circuit Diagram Extended-distance type Model Operating status Timing chart Output circuit 4 Brown Load +V Setting point Non-sensing zone Unstable sensing zone Stable sensing zone Main circuit 3 E2EQ-X4X1 E2EQ-X8X1 E2EQ-X15X1 E2EQ-X4X1-M1J E2EQ-X8X1-M1J E2EQ-X15X1-M1J Blue 0V Sensing object NO (%) 100 Rated sensing distance 80(TYP) 0 Lit Not lit Lit Not lit ON OFF Green indicator Red indicator Control output Note: 1. The load can be connected to either the +V or the 0-V line. Since there is no polarity, there is no need to pay attention to the brown or blue polarity. Wiring 1 2 3 4 Note: Terminals B and C are not used. Standard Model Operating status Timing chart Output circuit Brown Setting point Non-sensing zone Unstable sensing zone Stable sensing zone Main circuit 1 Main circuit Load +V E2EQ-X3D1 E2EQ-X7D1 E2EQ-X10D1 E2EQ-X3D1-M1GJ E2EQ-X7D1-M1GJ E2EQ-X10D1-M1GJ Sensing object (%) 100 80(TYP) 0 4 Blue 0V NO Rated sensing distance Lit Green indicator Not lit Lit Red indicator Not lit ON Control output OFF Note: The Load can be connected to either the +V or the 0-V line. Wiring A B C Note: Terminals B and C are not used. D Connecting Plug-in models Model E2EQ-X#X1-M1J E2EQ-X#D1-M1GJ Connector relay type E2EQ-X#X1-M1J Connection Main circuit 1 2 3 4 Sensor I/O Connectors XS2F-D42#-#C0-A 1 2 3 4 Connector relay type E2EQ-X#D1-M1GJ Brown not connected Blue (+) Black (-) Main circuit 1 2 3 4 Sensor I/O Connectors XS2F-D42#-#A0-A 1 2 3 4 Brown (+) Blue (-) E2EQ D-175 E2EQ Precautions Correct Use Design Effects of Surrounding Metal Provide a minimum distance between the Sensor and the surrounding metal as shown in the table below. Mounting Do not tighten the nut with excessive force. A washer must be used with the nut. Shielded Model l d dia. m Model E2EQ-X4X1(-M1J) E2EQ-X8X1(-M1J) E2EQ-X15X1(-M1J) E2EQ-X3D11(-M1GJ) E2EQ-X7D1(-M1GJ) E2EQ-X10D1(-M1GJ) 0 Item l 2. 4 3. 6 6 D n m l Part B Part A Effects of Surrounding Metal (Unit: mm) d 18 27 45 12 18 30 0 D 2. 4 3. 6 6 m 12 24 45 8 20 40 n 18 27 45 18 27 45 Note: 1 . The table below shows the tightening torques for part A and part B nuts. In the previous examples, the nut is on the sensor head side (part B) and hence the tightening torque for part B applies. If this nut is in part A, the tightening torque for part A applies instead. The table below shows the value of tightening torques when using toothed washers. Torque Model E2EQ-X4X1(-M1J) E2EQ-X8X1(-M1J) E2EQ-X15A(-M1J) E2EQ-X3D1(-M1GJ) E2EQ-X7D1(-M1GJ) E2EQ-X10D1(-M1GJ) 24 15 Nm --Length (mm) Part A Torque 30 Nm 70 Nm 180 Nm Part B Torque --- Mutual Interference If more than one Proximity Sensor is installed face to face or in parallel, make sure that the distances between two Units adjacent to each other are the same as or larger than the corresponding values shown in the following table. 29 26 39 Nm 78 Nm B A Mutual Interference(Unit: mm) Model E2EQ-X4X1(-M1J) E2EQ-X8X1(-M1J) E2EQ-X15X1(-M1J) E2EQ-X3D1(-M1GJ) E2EQ-X7D1(-M1GJ) E2EQ-X10D1(-M1GJ) Item A 30 60 110 30 50 100 B 20 35 90 20 35 70 D-176 Inductive Sensors Dimensions (Unit: mm) Pre-wired Models Extended-distance type E2EQ-X4X1 38 33 4 10 2 9 21 dia. 17 *1 M12 x 1 Indicator *2 Two, clamping nuts Toothed washer *1: Vinyl-insulated round cable (flame-resistant), 4 dia. [. . . ] 36 42 38 10 M18 x 1 4 *1 Indicator *2 Two, clamping nuts (Teflon coating) Two, toothed washer M30 x 1. 5 5 *1 Indicator *2 Two, clamping nuts (Teflon coating) Two, toothed washer *1: Vinyl-insulated round cable (flame-resistant), 6 dia. , 2 conductors (conducting cross-sectional area: 0. 5 mm2/insulator diameter: 1. 9 mm Standard length: 2m Cable extension (through a single metal conduit): 200m max. *2: Operation indicator (red) and setting indicator (green). *1: Vinyl-insulated round cable (flame-resistant), 6 dia. , 2 conductors (conducting cross-sectional area: 0. 5 mm2/insulator diameter: 1. 9 mm Standard length: 2m Cable extension (through a single metal conduit): 200m max. To convert millimeters into inches, multiply by 0. 03937. [. . . ]