User manual OMRON E2EZ DATASHEET

[. . . ] of sensing distance Ferrous metal (Sensitivity lowers with non-ferrous metals) Iron, 30 × 30 × 1 mm C models: 12 Hz Y models: 5 Hz Iron, 54 × 54 × 1 mm C models: 8 Hz Y models: 5 Hz Iron, 30 × 30 × 1 mm 100 Hz Iron, 54 × 54 × 1 mm 30 Hz E2EZ-X8C1 E2EZ-X8Y1 8 mm ±10% 0 to 6. 4 mm E2EZ-X4D@-N E2EZ-X4D@-M1J E2EZ-X4D@-M1GJ 4 mm ±10% 0 to 3. 2 mm E2EZ-X8D@-N E2EZ-X8D@-M1J E2EZ-X8D@-M1GJ 8 mm ±10% 0 to 6. 4 mm C models: 12 to 24 VDC, ripple (p-p) : 10% max. , (10 to 12 to 24 VDC (10 to 30 VDC) ripple (p-p): 10% max. VAC) Control output C models: NPN open collector output 12 VDC 100 mA Switching max. (30 VDC max. ) 3 to 100 mA capacity Y models: 10 to 200 mA Residual voltage C models: 2 V max. (load current: 200 mA with cable length: 2 m) Y models: Refer to the Specifications C models: Detection indicator (red LED) Y models: Operation indicator (red LED) 3. 0 V max. [. . . ] (M1GJ) 1 Load +V Pin arrangement 1 2 3 4 Main circuit 4 Note: The load can be connected to either the +V or the 0-V line. Non-sensing zone Sensing object Sensing zone 0V Note: Terminals B and C are not used. Load +V Brown Main circuit NC E2EZ-X4D2-N E2EZ-X8D2-N (%) 100 Rated sensing distance 0 Lit Not lit ON OFF Red Indicator Control output Blue 0V Note: The load can be connected to either the +V or the 0-V line. DC 3-wire Models Operating status Model Timing chart Output circuit Brown +V Load Yes Sensing object No Main circuit Black 2. 2 Output * NO E2EZ-X4C1 E2EZ-X8C1 Operate Load Reset ON Red Indicator OFF Blue 0V * Load current: 100mA max. at 24 V AC 2-wire Models Operating status Model Timing chart Output circuit Blown Sensing object Yes No Operate Reset ON OFF Main circuit Blue Load NO E2EZ-X4Y1 E2EZ-X8Y1 Load Red Indicator D-164 Inductive Sensors Precautions Correct Use Design Effects of Surrounding Metal Provide a minimum distance as shown in the table below between the Sensor and the surrounding metal. m n d dia. D l (1) About the external diameter (d) of a cut chip and the diameter (D) of the sensing surface If the external diameter (d) of a cut chip is two-thirds the diameter (D) of the sensing face as shown in the illustration. (Unit: mm) Model Length D 16 28 d Cut chips D Sensing face Pressed Cut chips Effects of Surrounding Metal (Unit: mm) Model E2EZ-X4@ E2EZ-X8@ Item SurroundSteel Aluminum Steel Aluminum l 0 5 0 10 d 18 40 30 70 D 0 5 0 10 m 16 32 n 27 54 45 90 E2EZ-X4@ E2EZ-X8@ Mutual Interference When installing two or more E2EZ face to face or side by side, ensure that the minimum distances given in the following table maintained. Mutual Interference (Unit: mm) Model E2EZ-X4@ E2EZ-X8@ Item A 40 60 B 50 100 (2) If cut chips are pressed onto the sending face as shown in the illustration. Mounting Do not tighten the nut with excessive force. A washer must be used with the nut. A B Part B Part A Aluminum and Cast Iron Cut Chips A detection signal will not be output if aluminum or cast iron cut chips are stuck to the sensing face. Under the following conditions, however, the proximity sensor may output detection signals, in which case remove the cut chips from the sensing face. Note: 1 . The table below shows the tightening torques for part A and part B nuts. In the previous examples, the nut is on the sensor head side (part B) and hence the tightening torque for part B applies. If this nut is in part A, the tightening torque for part A applies instead. The table below shows the value of tightening torques when using toothed washers. Tightening torgues Model E2EZ-X4C1 E2EZ-X4Y1 E2EZ-X8C1 E2EZ-X8Y1 E2EZ-X4D@-@ E2EZ-X8D@-@ Length (mm) 20 22 29 26 Part A Tensile strength (torque) 15 N·m 29 N·m 15 N·m 39 N·m Part B Tensile strength (torque) 29 N·m 39 N·m --78 N·m Dimensions (Unit: mm) 29 dia. 24 60 Indicator (see note 2) 80 E2EZ-X4C1 E2EZ-X4Y1 (see note 1) M18 x 1 Two toothed lock washer 4 4 Two tightening nuts 2. B, C Type: Detection indicator (red) Y Type: Operation indicator (red) Note: 1. E2EZ-X4B1 and E2EZ-X4CI: A 6 dia. , 3-conductor, vinyl-insulated round cable (conductor cross-sectional area: 0. 5 mm2; insulation diameter: 1. 9 mm) is used. Standard length: 2 m E2EZ-X4Y1 A 6 dia. , 2-conductor, vinyl-insulated round cable (conductor cross-sectional area: 0. 5 mm2; insulation diameter: 1. 9 mm) is used. Standard length: 2 m E2EZ D-165 E2EZ 42 dia. [. . . ] 2 cores conductor cross-sectional area: 0. 5 mm2; insulation diameter: 1. 9 mm) Standard length: 300 mm Connector relay type(-M1J/M1GJ) M12 x 1 16 dia. Vinyl-insulated round cable of 6 dia. 2 cores conductor cross-sectional area: 0. 5 mm2; insulation diameter: 1. 9 mm) Standard length: 300 mm Mounting Holes Model E2EZ-X4@ E2EZ-X8@ F F (mm) 18. 5-mm dia. +0 ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0. 03937. [. . . ]