User manual OMRON E3F2-240VAC DATASHEET

[. . . ] at 500 V DC between energized parts and case 1500 VAC, 50 / 60 Hz for 1 min between energized parts and case 10 to 55 Hz, 1. 5 mm double amplitude for 2 hrs each direction (X, Y, Z) 500 m/sqr (approx. 50 g) for each direction (X, Y, Z) IEC 60529: IP66 Infrared LED (880 nm) Light incident/power indicator for light source (red) Fixed 2 m, 5 m pre-wired cable (PVC dia. 4 mm (14 / 0. 15) *2) Light-ON or Dark-ON (fixed) None 110 g (pre-wired 2 m cable) Plastic (case: ABS; lens: PMMA) For sensing distance in detail, please refer to "Engineering Data" For other cable materials (e. g. PUR) please contact your OMRON sales representative. 2 Standard Photoelectric Sensors Engineering Data (Typical) Operating Range (typical) Through-beam Models E3F2-3Z# Retro-reflective Models E3F2-R2Z# (non polarizing) and reflectors typical sensing distance: 3. 8 m 300 typical sensing distances: E39-R1: 3. 4 m E39-R7: 3. 9 m E39-R8: 5. 2 m Diffuse-reflective Models E3F2-DS10Z-# (wide-beam type) 30 300 200 200 20 Distance Y (mm) 100 Distance Y (mm) Distance Y (mm) 100 10 0 0 0 white paper (50 x 50 mm) ­100 ­100 ­10 ­200 Y ­300 0 1 2 3 X 4 5 ­200 Y ­300 0 1 2 3 4 5 6 X 7 8 Reflector ­20 Y X ­30 0 20 40 60 80 100 120 140 Object Distance X (m) Distance X (m) Distance X (mm) Excess Gain Ratio vs. [. . . ] Otherwise, parts may become damaged and the degree of protection may be degraded. High-temperature environments may result in burn injury. Outdoor Use Do not use the Sensor in locations subject to direct sunlight. Cleaning Do not use thinner, alcohol, or other organic solvents. Otherwise, the optical properties and degree of protection may be degraded. Surface Temperature Burn injury may occur. The Sensor surface temperature rises depending on application conditions, such as the surrounding temperature and the power supply voltage. Use caution when operating or washing the Sensor. Precautions for Correct Use Do not use the Sensor in any atmosphere or environment that exceeds the ratings. Do not install the Sensor in the following locations. Precautions for Safe Use The following precautions must be observed to ensure safe operation of the Sensor. (1) Locations subject to direct sunlight (2) Locations subject to condensation due to high humidity (3) Locations subject to corrosive gas (4) Locations where the Sensor may receive direct vibration or shock Operating Environment Do not use the Sensor in an environment where explosive or flammable gas is present. Connecting and Mounting (1) Laying Sensor wiring in the same conduit or duct as high-voltage wires or power lines may result in malfunction or damage due to induction. As a general rule, wire the Sensor in a separate conduit or use shielded cable. (2) Do not pull on the cable with excessive force. (3) Do not subject the photoelectric sensor to excessive shock when mounting, in keeping with IP66 standards. (4)Mount the Sensor using a bracket (sold separately). Do not exceed a torque of 2. 0 Nm when tightening mounting nuts. Load Do not use a load that exceeds the rated load. Do not connect the black wire to the brown wire without a load. Direct connection of these wires may damage the photoelectric sensor Brown Load Sensor Black 24 to 240 VAC Cleaning Never use thinner or other solvents. Otherwise, the Sensor surface may be dissolved. Blue Water Resistance Do not use the Sensor in water, rainfall, or outdoors. When you use the photoelectric sensor at temperatures exceeding 45°C, the load current must be within the described values as shown in the figure below. 200 Load current (mA) 130 0 45 55 Operating temperature (°C) 6 Standard Photoelectric Sensors E3F2-240VAC 7 WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. LIMITATIONS OF LIABILITY OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. In no event shall responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted. IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR. SUITABILITY FOR USE THE PRODUCTS CONTAINED IN THIS DOCUMENT ARE NOT SAFETY RATED. [. . . ] NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. PERFORMANCE DATA Performance data given in this document is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of OMRON's test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON Warranty and Limitations of Liability. [. . . ]