User manual OMRON E3S-C DATASHEET

[. . . ] ------E3S-C * Values in parentheses indicate the minimum required distance between the sensor and reflector. When the reflector used is other than the supplied one, set the sensing distance to about 0. 7 times of the typical example as a guideline. Mounting Brackets Shape Model Quantity Remarks E39-L102 1 Attached to the horizontal model. E39-L103 1 Attached to the vertical model. E39-L85 1 Mounting bracket designed to switch from E3S-#####42, 44 to the vertical model of E3S-C. E39-L86 1 Mounting bracket designed to switch from E3S-#####43 to the vertical model of E3SC. E39-L87 1 --- Note: If a through-beam model is used, order two Mounting Brackets for the emitter and receiver respectively. Sensor I/O Connectors Cable Shape Cable length 2m 5m 3-wire type XS2F-D422-DC0-A XS2F-D422-GC0-A Model XS2F-D421-DC0-A XS2F-D421-GC0-A Straight Standard cable L-shaped 2m 5m E3S-C A-103 Rating/performance Sensor type Model Through-beam Horizontal E3S-CT11 (-M1J) Vertical E3S-CT61 (-M1J) 30 m Opaque, 15dia. function) Horizontal E3S-CR11 (-M1J) Vertical E3S-CR61 (-M1J) 3 m (When using the E39-R1) Opaque: 75 mm dia. --Both emitter and receiver: 3° to 15° Infrared LED (880 nm) 3° to 10° Red LED (700 nm) Infrared LED (880 nm) Diffuse-reflective Horizontal E3S-CD11 (-M1J) Horizontal E3S-CD12 (-M1J) Vertical E3S-CD61 (-M1J) 700 mm (White paper 300 x 300 mm) Vertical E3S-CD62 (-M1J) 2 m (White paper 300 x 300 mm) --20% max. [. . . ] Remove the sensing object, turn the sensitivity adjuster further clockwise until the incident indicator (red) is turned ON by a background object, and define this position as (B). Turn the sensitivity adjuster counterclockwise (decrease sensitivity) from (B) until the incident indicator (red) is turned OFF, and define this position as (C). When there is no background object, define the maximum adjuster position (Max) as (C). Set the adjuster in the middle of positions (A) and (C) (optimum sensitivity setting). Also make sure that the stability indicator (green) is turned ON when there is an object and when there is no object. · When the sensor cannot be set on the mechanical axis, move the E3S-C vertically and/or horizontally and set it in the center of the area where the incident indicator is turned ON. Make sure that the stability indicator is ON. Optical axis Mounting axis Four M4 optical axis lock holes E3S-C A-107 E3S-C Optical axis position of through-beam model Unlike the conventional product, the through-beam model has two lenses, but the one actually used is as shown below. When fitting the slit, use it after matching the slit hole with the used lens. (Horizontal model) (Vertical model) Lens in use. Lens in use. Miscellaneous Oil resistance/chemical resistance · Though E3S-C has a high oil resistance, it may not be able to exhibit its performance depending on the oil type. Use oil in compliance with the following table. · Regarding the oil resistance of E3S-C, it has passed tests on the oils given in the following table. Refer to the table for examining the oil to be used. Testing JIS classioil classification fication Product name Velocity No. 2ac Yushiroken EC50T-3 Yushiron Lubic HWC68 Gryton 1700D Yushiroken S50N --Dynamic viscosity (mm2/s) at 40°C 2. 02 Not less than 10 to less than 50 Less than 10 7 to 9. 5 7 to 9. 9 7 to 9. 2 7 to 9. 8 PH Lens not in use. Lens not in use. Lubricant Water-insoluble coolant --Class 2 No. 1 --- Water Resistance To ensure water resistance, tighten the operation panel cover screws to 0. 34 Nm to 0. 54 Nm torque. Watersoluble coolant Class W1 No. The E3S-C was immersed in the oils in the above table at 50°C for 240 hours, and passed the test of 100-M or more insulation resistance. For use in the environment where the E3S-C is exposed to the oil other than those in the above table, use the dynamic viscosity and PH in the above table. [. . . ] (27¥12 dia. ). Retro/diffuse reflective model (horizontal model) E3S-CR11(-M1J) E3S-CD11(-M1J) E3S-CD12(-M1J) With mounting bracket Junction connector models (-M1J) Vinyl-insulated round cable with three conductors, 4 dia. (18 x 0. 12 dia. ); standard length: 0. 3 m M12 x 1 16 dia. 18. 5 50 Light indicator (red) M3 x 5 Vinyl-insulated round cable with three conductors, 4 dia. (18 x 0. 12 dia. ); standard length: 2 m * 3 20 20. 4 22. 2 Stability indicator (green) 9. 2 4. 2 Mounting holes 2-M4 20 25. 4 4. 2 8. 3 Stainless steel (SUS304) Lens (17 x 11) Receiver 2. 2 6. 2 38. 2 23 4 9 1 18 (A)*1 29. 5 17. 3 9. 3 Optical axis Emitter 2-M4 1. 5 20. 8 25. 4 * Note: Mounting bracket can be attached to side A. E3S-C A-109 E3S-C Vinyl-insulated round cable with three conductors, 4 dia. (18¥0. 12 dia. ); standard length: 0. 3 m M12¥1 Retro/diffuse reflective model (vertical model) E3S-CR61(-M1J) E3S-CD61(-M1J) E3S-CD62(-M1J) Vinyl-insulated round cable with three conductors, 4 dia. [. . . ]