User manual OMRON E5 K-T DATASHEET

[. . . ] Press the Up Key to increment to "100. " 5p1 0 100 Down key 3. Press the Display Key to shift to the display for the target value of step 0. Up key 5p0 0 0 Step 0 Parameter of the target value Target value (Default setting: 0) In the same manner, set the time for step 1, target value for step 2, time for step 2, etc. When the target value and time settings are complete, press the Display Key. Display key I-124 Digital Controller E5@K-T Digital Controller E5AK-T/E5EK-T Advanced Programmable Digital Controllers Ideal for Worldwide Use · Offers up to eight patterns of simple programming control (16 steps per pattern). · Modular structure, one-stock type · High-accuracy: 100-ms sampling (for analog input) · Conforms to international EMC and safety standards. [. . . ] · IP66/NEMA4 (indoor use) front face. · Modular structure, one-stock type. · Serial communications (RS-232C and RS-485). · High-accuracy: 100-ms sampling (for analog input). · Conforms to international EMC and safety standards. · 24 VAC/DC types are also available. ® Ordering Information List of Models Description Base Unit Model E5CK-TAA1 AC100-240 E5CK-TAA1-500 AC100-240 E5CK-TAA1 AC/DC24 E5CK-TAA1-500 AC/DC24 Note: A single Output Unit and Option Unit can be mounted to each Base Unit. Description Output Unit E53-R4R4 E53-Q4R4 E53-Q4HR4 E53-C4R4 E53-C4DR4 E53-V44R4 E53-Q4Q4 E53-Q4HQ4H Description Option Unit E53-CK01 E53-CK03 E53-CKB E53-CKF Model RS-232C RS-485 Event input: 1 point Transfer output (4 to 20 mA) Model Relay/Relay Pulse (NPN)/Relay Linear (4 to 20 mA)/Relay Linear (0 to 20 mA)/Relay Linear (0 to 10 V)/Relay Pulse (NPN)/Pulse (NPN) Pulse (PNP)/Pulse (PNP) Specification Temperature Controller Pulse (PNP)/Relay Specification Standard model Standard model with terminal cover Standard model Standard model with terminal cover Specification Inspection Report The Digital Controller can be provided together with an inspection report. Refer to the following legend with the suffix "K" when ordering a model provided together with an inspection report. E5CK-TAA1-K Accessories (Order Separately) Name Terminal Cover E53-COV07 Model Digital Controller E5CK-T I-127 Precautions !WARNING Do not touch any of the terminals while the power is being supplied. If there is a large power-generating peripheral device and any of its lines near the Controller, attach a surge suppressor or noise filter to the device to stop the noise affecting the Controller system. In particular, motors, transformers, solenoids and magnetic coils have an inductance component, and therefore can generate very strong noise. When mounting a noise filter on the power supply to the Controller, be sure to first check the filter's voltage and current capacity, and then mount the filter as close as possible to the Controller. Use within the following temperature and humidity ranges: · Temperature: ­10°C to 55°C (with no icing or condensation) Humidity: 35% to 85% (with no icing or condensation) If the Controller is installed inside a control board, the ambient temperature must be kept to under 55°C, including the temperature around the Controller. If the Controller is subjected to heat radiation, use a fan to cool the surface of the Controller to under 55°C. Store within the following temperature and humidity ranges: · Temperature: ­25°C to 65°C (with no icing or condensation) Humidity: 35% to 85% (with no icing or condensation) Never place heavy objects on, or apply pressure to the Controller that may cause it to deform and deteriorate during use or storage. Avoid using the Controller in places near a radio, television set, or wireless installing. These devices can cause radio disturbances which adversely affect the performance of the Controller. General Precautions Be sure to observe these precautions to ensure safe use. · Do not use the product in places where explosive or flammable gases may be present. · Never disassemble, repair or modify the product. · Tighten the terminal screws properly. · Use the specified size of solderless terminals for wiring. · Use the product within the rated supply voltage. [. . . ] Recommended panel thickness is 1 to 8 mm (1 to 5 mm for E5CK). Mount the Unit horizontally. Connection To reduce inductive noise influence, the lead wires connecting the input type to the Digital Controller must be separated from the power lines and load lines. Use the specified compensating conductors for thermocouples. Use lead wires having a small resistance for platinum resistance thermometers. Connection Example Wire the terminals of the Unit using solderless terminals. [. . . ]