User manual OMRON E5ZE-8 D1 B-V2 DATASHEET

[. . . ] Refer to the List of Models for combinations of functions. Multipoint Temperature Controller E5ZE-8@D1@B-V2 1 Ordering Information List of Models No. of control points 8 Control method Control output Heater burnout and SSR failure detection Available (see note 2) Not available Available (see note 2) Not available Input type Thermocouple Platinum resistance thermometer E5ZE-8ACAD1PB-V2 Standard (see note 1) Heating and cooling Voltage Current Voltage Current (see note 3) E5ZE-8AQHD1TCB-V2 E5ZE-8AQHD1PB-V2 E5ZE-8ACAD1TCB-V2 E5ZE-8VQHD1TCB-V2 E5ZE-8VQHD1PB-V2 E5ZE-8VCAD1TCB-V2 E5ZE-8VCAD1PB-V2 Note: 1. Cooling control is possible by making a change in output operation. Models without the heater burnout/SSR failure detection function are also available. [. . . ] setting 1°C or 0. 1°C unit Platinum Resistance Thermometer Input (switch selectable) Range Setting no. setting unit Pt 100 (see note 1) ­100. 0 to 500. 0 ­100. 0 to 900. 0 0 1°C or 0. 1°C JPt 100 ­100. 0 to 500. 0 ­100. 0 to 900. 0 1 Note: 1. A temperature range is factory-set to a range of ­200° to 1, 300°C (for K(CA)) or ­100. 0° to 500. 0°C (for Pt 100). Thermocouple W is W/Re5-26 (tungsten rhenium 5, tungsten rhenium 26). °C °F Characteristics Measurement accuracy (see note) Thermocouple: (±0. 3% of the process value or ±2°C, whichever greater) ±1 digit max. (±0. 3% of the process value or ±3. 6°F, whichever greater) ±1 digit max. Platinum resistance thermometer: (±0. 3% of the process value or ±0. 8°C, whichever greater) ±1 digit max. (±0. 3% of the process value or ±1. 5°F, whichever greater) ±1 digit max. 0. 0° to 99. 9°C/°F for ON/OFF control only (in units of 0. 1°C/°F) 0. 0 to 10. 0 (in units of 0. 1) 0. 0° to 999. 9°C/°F (in units of 0. 1°C/°F) Cooling side: Cooling coefficient × Proportional band 0 to 3, 999 s (in units of 1 s) (for both heating and cooling) 0 to 3, 999 s (in units of 1 s) (for both heating and cooling) Heating side: Cooling side: 1 to 99 s (in units of 1 s) 1 to 99 s (in units of 1 s) Hysteresis Cooling coefficient Proportional band Integral (reset) time Derivative (rate) time Control period Sampling period Dead band/overlap band Alarm output setting range 200 ms for 8 control points ­999° to 999°C/°F (in units of 1°C/°F) ­999° to 9999°C/°F, 0 to 9999°C/°F (upper- and lower-limit alarm) (in units of 1°C/°F) ­999. 9° to 9999. 9°C/°F, 0. 0 to 9999. 9°C/°F (upper- and lower-limit alarm) (in units of 0. 1°C/°F) (see note 3) 0% to 99% (in units of 1%) 0. 2° to 999. 9°C/°F (in units of 0. 1°C/°F) 0. 02° to 99. 99°C/s or °F/s (in units of 0. 01°C/s or °F/s) Lithium battery 10 years min. provided that the ambient temperature is within the room temperature 20 M min. between the FG terminal and all analog input terminals (at 500 VDC) A leakage current of 1 mA AC max. with 500 VAC for 1 minutes between the FG terminal and all analog input terminals Malfunction: 10 to 55 Hz, 15 m/s2 for 8 min each in X, Y, and Z directions Destruction: 10 to 55 Hz, 20 m/s2 for 8 min each in X, Y, and Z directions Malfunction: 150 m/s2, 3 times each in 6 directions Destruction: 200 m/s2, 3 times each in 6 directions Operating: Storage: Operating: Storage: 0° to 55°C (with no icing or condensation) ­25° to 65°C (with no icing or condensation) 35% to 85% 35% to 95% Fuzzy strength Fuzzy scale 1 Fuzzy scale 2 Set value backup Set value backup period Insulation resistance Dielectric strength Vibration resistance Shock resistance Ambient temperature Ambient humidity 4 Multipoint Temperature Controller E5ZE-8@D1@B-V2 Dimensions Enclosure rating Weight With casing: 173. 5 x 253 x 65 mm max. IP00 With casing:1, 700 g max. Note: 1. The measurement accuracy of the E5ZE used with a thermocouple B at 400°C or 750°F max. The following measurement accuracy values are applied to the E5ZE. and U: ±3°C ±1 digit max. and U: ±5. 4°F ±1 digit max. R, S, and W at 200°C max. , and B at 1, 000°C max. : ±4°C ±1 digit max. R, S, and W at 400°F max. , and B at 1, 800°F max. : ±7. 2°F ±1 digit max. The measurement accuracy of the E5ZE used with any thermocouple is 1°C/°F. The thermocouple can be used under the following temperature ranges to increase the measurement accuracy to as high as 0. 1°C/°F. [. . . ] The mounting brackets must be attached to the E5ZE with the four M3×6 screws provided with the E5ZE and each of the screws should be tightened to a torque of 0. 43 to 0. 58 N·m, or 4. 4 to 5. 9 kgf·cm. · Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog. · Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. · Systems, machines, and equipment that could present a risk to life or property. [. . . ]