User manual OMRON F3S-TGR-N C DATASHEET

[. . . ] Type L: S: M: Elongated Sensor Small Sensor for NLPC and NSMC Miniature Sensor 2. Housing Material P: Plastic Housing M: Stainless Steel Housing 3: Contact configuration 20: 2 Normally Closed Contacts (NC) 21: 2 Normally Closed Contacts (NC) + 1 Normally Open Contact (NO) 4: Cable Length/connection 02: 2m Cable 05: 5m Cable 10: 10m Cable M1J8: M12 male connector, 8pin 4: Cable Length/connection for NMPC 02: 2m Cable, cable exit to the left 05: 5m Cable, cable exit to the left 10: 10m Cable, cable exit to the left M1J8: M12 male connector, 8-pin, cable exit to the left F3S-TGR-N@C 1 Ordering Information Elongated Sensors Type F3S-TGR-NLPC-20-02 F3S-TGR-NLPC-20-05 * F3S-TGR-NLPC-20-10 F3S-TGR-NLPC-20-M1J8 F3S-TGR-NLPC-21-02 F3S-TGR-NLPC-21-05 * F3S-TGR-NLPC-21-10 F3S-TGR-NLPC-21-M1J8 Cable Connection 2 m pre-wired 5 m pre-wired 10 pre-wired M12, 8-pin 2 m pre-wired 5 m pre-wired 10 pre-wired M12, 8-pin Contact Configuration 2NC 2NC 2NC 2NC 2NC/1NO 2NC/1NO 2NC/1NO 2NC/1NO *. Preferred stock items. Small Sensor Type F3S-TGR-NSMC-20-02 F3S-TGR-NSMC-20-05 * F3S-TGR-NSMC-20-10 F3S-TGR-NSMC-20-M1J8 F3S-TGR-NSMC-21-02 F3S-TGR-NSMC-21-05 * F3S-TGR-NSMC-21-10 F3S-TGR-NSMC-21-M1J8 Cable Connection 2 m pre-wired 5 m pre-wired 10 pre-wired M12, 8-pin 2 m pre-wired 5 m pre-wired 10 pre-wired M12, 8-pin Contact Configuration 2NC 2NC 2NC 2NC 2NC/1NO 2NC/1NO 2NC/1NO 2NC/1NO *. [. . . ] EN954-1) +24V GND Start A1 A2 T31 KM1 Feedbackloop Magnetic Actuator F3S-TGR-NxxC Sensor red blue black white yellow green brown orange G9SB-2002-C T11 T12 T22 T21 NO contact KM2 T32 KM1 13 14 KM1 23 24 KM2 KM2 +Us GND Series connection Application, up to 6 Sensors with G9SB-2002-C (up to safety Category 3 acc. EN954-1) Magnetic Actuator F3S-TGR-NxxC Sensor red blue black white yellow green M +24V GND Start A1 A2 T31 KM1 Feedbackloop Magnetic Actuator F3S-TGR-NxxC Sensor red blue black white yellow green G9SB-2002-C T11 T12 T22 T21 T32 KM2 KM1 Magnetic Actuator F3S-TGR-NxxC Sensor red blue black white yellow green 13 14 KM1 23 24 KM2 KM2 +Us GND M 8 Safety Sensors / Components G9SX Single Sensor Application with G9SX-AD322-T15 (up to Safety Category 4 acc. EN954-1) +24V GND Start A1 T33 A2 T31 KM1 Feedbackloop Magnetic Actuator F3S-TGR-NxxC Sensor red blue black white yellow green brown orange G9SX-AD322 T11 T12 T21 T22 NO contact KM2 T32 KM1 S14 KM1 S24 KM2 KM2 M GND Series connection Application, up to 6 Sensors with G9SX-AD322-T15 (up to Safety Category 3 acc. EN954-1) +24V Magnetic Actuator F3S-TGR-NxxC Sensor red blue black white yellow green GND Start A1 T33 A2 T31 KM1 Feedbackloop Magnetic Actuator F3S-TGR-NxxC Sensor red blue black white yellow green G9SX-AD322 T11 T12 T21 T22 T32 KM2 KM1 Magnetic Actuator F3S-TGR-NxxC Sensor red blue black white yellow green S14 KM1 S24 KM2 KM2 M GND F3S-TGR-N@C 9 DeviceNet Safety NE1A and DST1-I/O-Terminals Single Sensor Application with NE1A and DST1-Safety-IO (up to safety Category 4 acc. EN954-1) +24V GND V0 G0 Magnetic Actuator F3S-TGR-NxxC Sensor red blue black white yellow green brown orange Test 0 In 0 Test 1 In 1 NO contact NE1A-. . . DST1-ID DST1-MD DST1-MRD Series connection Application, up to 6 Sensors with NE1A or DST1-Safety-IO (up to Safety Category 3 acc. EN954-1) +24V Magnetic Actuator F3S-TGR-NxxC Sensor red blue black white yellow green GND V0 G0 Magnetic Actuator F3S-TGR-NxxC Sensor red blue black white yellow green Test 0 In 0 Test 1 In 1 Magnetic Actuator F3S-TGR-NxxC Sensor red blue black white yellow green NE1A-. . . DST1-ID DST1-MD DST1-MRD Application with multiple Sensors with NE1A or DST1-Safety-IO (up to Safety Category 4 acc. EN954-1) Magnetic Actuator F3S-TGR-NxxC Sensor red blue black white yellow green +24V GND V0 Test 0 Test 1 G0 Magnetic Actuator F3S-TGR-NxxC Sensor red blue black white yellow green Test 2 In 0 In 1 In 2 In 3 Switch 1: Test 0 In 0 Test 1 In 1 Switch 2: Test 0 In 2 Test 2 In 3 Switch 3: Test 1 In 4 Test 2 In 5 Magnetic Actuator F3S-TGR-NxxC Sensor red blue black white yellow green NE1A-. . . DST1-ID DST1-MD In 4 In 5 10 Safety Sensors / Components Safety Precautions !WARNING Be sure to turn OFF the power before performing wiring. Do not touch charge parts (e. g. , terminals) while power is ON. Do not allow the actuator to come close to the switch with the door open. Doing so may cause machinery to start operating and may result in injury. Keep actuators (magnets) away from magnetically sensitive equipment like PC harddisks, floppy disks etc. The magnetic field of the magnet will damage existing data. Mutual Interference If the switch and actuator are mounted in parallel, be sure to separate them by at least 25 mm, as shown below. 25 mm min. Switch Actuator Guard door Switch Actuator Using for Hinged Doors On hinged doors, install the Sensor at an opening edge as shown below. !CAUTION Use guard stops in the way shown below to ensure that the switch and actuator do not make contact when the guard door is closed. Guard door Switch Guard Stops Actuator CORRECT 2 mm INCORRECT Solvents Ensure that solvents, such as alcohol, thinner, trichloroethane, or gasoline do not adhere to the product. [. . . ] Do not use power supplies with large ripples or power supplies that intermittently generate incorrect voltages. · Capacitors are consumable and require regular maintenance and inspection. · Locations subject to direct sunlight · Locations subject to humidity levels outside the range 35% to 85% or subject to condensation due to extreme temperature changes · Locations subject to corrosive or flammable gases · Locations subject to shocks or vibration in excess of the product ratings · Locations subject to dust (including iron dust) or salts Take appropiate and sufficient countermeasures when using the product in the following locations. · · · · Locations subject to static electricity or other forms of noise Locations subject to possible exposure to radioactivity Locations subject to power supply lines It is advisable to mount the switches on non ferrous materials. [. . . ]