User manual OMRON H3Y DATASHEET

[. . . ] LED indication for power and output statuses. High repeat accuracy. H3Y RC Ordering Information Operation/resetting Ope a o / ese g t system Time-limit operation/ e o ea o / self-resetting lf tti Time-limit contact e co ac Time ranges e a ges Supply voltage Supp y o age Model Surface /DIN-track mounting (with socket) DPDT 0 0. 1 s to 30 min o 110 VAC 220 VAC 24 VDC 4PDT 110 VAC 220 VAC 24 VDC Note: Specify the model number, supply voltage, and rated time when ordering. H3Y-2 110 VAC 1s Rated time Supply voltage H3Y-4 3 H3Y-2 3 Accessories Track mounted socket (see note ) ac ou ed soc e oe Solder terminal PYF08A, PYF08A-N, PYF08A-E PYF14A, PYF14A-N, PYF14A-E Note: PY08 PY14 Back connecting socket Wire-wrap terminal PY08QN(2) PY14QN(2) PY08-02 PY14-02 PC terminal Track mounted socket can be used as a front connecting socket. Specifications Time Ranges Rated time Time setting range 1s 0. 1 to 1 s 5s 0. 2 to 5 s 10 s 0. 5 to 10 s 30 s 1. 0 to 30 s 60 s 2. 0 to 60 s 3 min 0. 1 to 3 min 30 min 1. 0 to 30 min 1 H3Y Ratings Item Rated supply voltage Operating voltage range Power consumption 85% to 110% of rated supply voltage 100 VAC: Relay ON: Relay OFF: 200 VAC: Relay ON: Relay OFF: 24 VDC: Relay ON: Relay OFF: 1. 5 VA (1. 3 W) 0. 8 VA (0. 5 W) 1. 8 VA (1. 5 W) 1. 2 VA (0. 9 W) 0. 9 W 0. 07 W H3Y-2/H3Y-4 110, 220 VAC (50/60 Hz), 24 VDC (see note) H3Y Control outputs Note: H3Y-2: 5 A at 250 VAC, resistive load (cos = 1) H3Y-4: 3 A at 250 VAC, resistive load (cos = 1) With DC ratings, single-phase full-wave rectified power sources may be used. Characteristics Accuracy of operating time Setting error Reset time Influence of voltage Influence of temperature Insulation resistance Dielectric strength ±2% max. [. . . ] Maximum current of 0. 2 A can be switched if L/R is 7 ms. In both cases, a life of 100, 000 operations can be expected. The minimum applicable load is 1 mA at 1 VDC (P reference value). Load current (A) Load current (A) Operation Timing Chart H3Y-2 H3Y-4 Time limit contact NC (9-1, 12-4) Time limit contact NC (9-1, 10-2, 11-3, 12-4) 3 H3Y H3Y Dimensions Note: All units are in millimeters unless otherwise indicated. Timers H3Y-2 H3Y-4 28 max. 6. 3 28 max. 6. 4 (63. 0) Accessories (Order Separately) Use the PYFjA, PYj, PYj-02, or PYjQN(2) to mount the H3Y. When ordering any one of these sockets, replace "j" with "08" or "14. " Track Mounting/Front Connecting Sockets PYF08A Two, 4. 2 × 5 mounting holes 6 Eight, M3 × 8 sems 3. 4 Terminal Arrangement (Top View) Mounting Holes Two, 4. 5 dia. 35. 4 59±0. 3 90. 5 86. 6 4 6 23 max. 16. 5 30 max. PYFjA 15±0. 2 PYF14A Two, 4. 2 × 5 mounting holes 6 3. 4 Fourteen, M3 × 8 sems Terminal Arrangement (Top View) Mounting Holes Two, 4. 5 dia. M4 or M3 72 max. 35. 4 59±0. 3 4 29. 5 max. 6 22±0. 2 4 H3Y PYF08A-N 22 max. H3Y Terminal Arrangement 42 4 44 8 12 1 14 5 Mounting Holes (for Surface Mounting) 4 42 8 44 1 12 5 14 3. 2 dia. 19. 8 3. 6 dia. PYF-08A-N 41 12 11 9 12 41 14 9 11 14 13 A2 A2 A1 14 14 13 A2 A2 A1 30 max. PYF14A-N Terminal Arrangement 4 42 8 44 3 32 7 34 2 22 6 24 1 12 5 14 42 32 22 12 4321 44 34 24 14 8765 Mounting Holes (for Surface Mounting) Two, 3. 5 dia. 66. 5 max. PYF-14A-N 41 12 31 11 21 10 11 9 20. 8 12 11 10 9 41 31 21 11 14 14 A2 A2 13 A1 A2 14 A2 14 A1 13 30 max. 29. 5 max. PYF08A-E Two, 4. 2 × 5 mounting holes Eight, M3 × 8 sems (Top View) Two, 4. 5 dia. 31 max. PYF14A-E Two, 4. 2 × 5 mounting holes Eight, M3 × 8 sems (Top View) Two, 4. 5 dia. 31 max. 5 H3Y Back Connecting Sockets PY08, PY14 Eight, 3 × 1. 2 dia. holes only for PY08 (Fourteen, 3 × 1. 2 dia. 2. 6 29. 5 max. H3Y Terminal Arrangement (Bottom View) Panel Cutout 21. 4 0 +0. 2 59. 3 25. 8 +0. 2 0 H3Y Series 2. 7 20 max. 7. 7 PY08 PY14 PYj, PYj-02, PYjQN(2) PY08QN, PY14QN PY08QN(2), PY14QN(2) 2. 7 25 max. 22 max. Terminal Arrangement (Bottom View) 29. 5 max. ** 41. 5 max. (see note) Note: 1x1 PY08QN PY08QN(2) PY14QN PY14QN(2) With PYjQN(2), dimension * should read 20 max. and dimension ** 36. 5 max. PY08-02, PY14-02 22 max. 2 Terminal Arrangement (Bottom View) 2. 7 16. 5 max. 4. 3 PY08-02 PY14-02 6 H3Y Socket Mounting Plates (t = 1. 6) Applicable socket PY08, PY14, PY08QN(2), PY14QN(2) Note: PYP-1 Two, 3. 4-dia. [. . . ] Make sure that there is a space of 5 mm or more between any H3Y Models next to each other to allow heat radiation. The internal parts may become damaged if a supply voltage other than the rated ones is imposed on the H3Y. When more than 100 V is applied to 12 or 24 VDC, the internal element (varistor) may break. Do not connect the H3Y as shown in the following circuit diagram on the right hand side, otherwise the H3Y's internal contacts different from each other in polarity may become short-circuited. Correct Incorrect Limited issue for Southeast Asian countries ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0. 03937. [. . . ]