User manual OMRON NSH5

[. . . ] V090-E1-07 NSH5 Series NSH5-SQR00B-V2 NSH5-SQG00B-V2 NSH5-SQR10B-V2 NSH5-SQG10B-V2 Hand-held Programmable Terminal OPERATION MANUAL NSH5 Series NSH5-SQR00B-V2 NSH5-SQG00B-V2 NSH5-SQR10B-V2 NSH5-SQG10B-V2 Hand-held Programmable Terminal Operation Manual Revised June 2008 iv Notice: OMRON products are manufactured for use according to proper procedures by a qualified operator and only for the purposes described in this manual. The following conventions are used to indicate and classify precautions in this manual. Always heed the information provided with them. Failure to heed precautions can result in injury to people or damage to property. !DANGER !WARNING Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. [. . . ] · Using a recovery/upgrade program · Transferring system program data Note (1) The system program must be version 8. 0 or higher to be installed. (2) Consult your OMRON representative if a system program of a version lower than 8. 0 is to be installed. (3) Use the recovery/update program to install the system program. Using a Recovery/ Upgrade Program Use the following procedure to replace the system program if the system program becomes corrupted and the PT will not start or to upgrade the system program in the PT. 40 Memory Cards 1, 2, 3. . . Section 3-5 1. Copy all of the files and folders in the RecoverUpdate_@_@ folder inside the CX-Designer installation folder (default: C:\ProgramFiles\Omron\CXOne\CX-Designer) to a Memory Card. This program can be selected when installing the CX-Designer. ("@_@" will be replaced by numbers indicating the system program version. For example "RecoverUpdate_7_0" is the file for version 7. 0. ) 2. Insert the Memory Card into the PT and turn ON the power supply. The recovery/update program will start automatically. The indicator will flash green when the download has been completed normally. Note (1) For details on the recovery/update program, select Start - Program OMRON - CX-One - CX-Designer - How to recover the system prog Ver. (2) Refer to information on the procedure for recovery and update and to the Setup Manual for troubleshooting information if an error is displayed when you use the recovery/update program. Transferring System Program Data The System Program is stored under the CX-Designer's install folder (default location is C:\Program Files\Omron\CX-One\CX-Designer) in folders that are created for each type and version, as follows: \SystemBackup\NSH5\V@_@\bank1: NSH5 system program ("@_@" will be replaced by numbers indicating the system program version. For example "RecoverUpdate_7_0" is the file for version 7. 0. ) To replace a system program, use Windows Explorer or another method to copy each of the folders for the required system program under \bank1 to the route directory of the Memory Card. For details on methods for transferring data from the Memory Card to the PT, refer to 3-5-4 Transferring Data with Memory Cards. The system backup folder can be created only if CX-Designer is installed from the stand-alone CD-ROM. If the CX-Designer is installed from CX-One, reinstall the system program by following the procedure for using a recovery/ update program described above. 3-5-4 Transferring Data with Memory Cards Using a Memory Card with the PT allows system programs (programs required for operating the PT, such as programs for communications and fonts) and screen data to be transferred to and from the PT. There are several types of data transfers, including manual transfers (in which the data to be transferred and the direction of transfer are selected manually), downloads (in which data is transferred automatically from the Memory Card to the PT), uploads (in which data is transferred automatically from the PT to the Memory Card), and bank specifications (four banks max. ). The transfer method is specified using the System Menu. Note (1) Before transferring data, check to be sure that the system programs and screen data types match those in the PT. (2) Do not perform the following operations while accessing the Memory Card. The data may be damaged and the Memory Card may need to be formatted. · Turning OFF the power to the PT. [. . . ] Pages 3, 4, 5, 9, 36, and 57: Emergency stop switch contact structure corrected. August 2006 Revised to add Removable Box. October 2007 Overall: Changed "NSH Series" to NSH5 Series. " Pages xix, 3 to 6, 8, 9, 23, and 71: Corrected "emergency stop switch". Page xxi: Removed next to last paragraph before section 5. [. . . ]