User manual OMRON S82J

[. . . ] Switch Mode Power Supply S82J (10/25/50/100/150/300/600-W Models) Low-cost Global Power Supply with CE Marking · Safety standards: UL: UL508, No. 60950-1 Class 2, CSA: cUL: C22. 2 No. 14, cUR: 60950-1 Class 2, EN60950-1 (=VDE0805 Teil 1), EN50178 (=VDE0160) · EMC: Conforms to EN61204-3 Class A · Mounting bracket available for standard models Front-mounting bracket type DIN Rail mounting type (except 300 W and 600 W) Note: Refer to Precautions for Safe Use on page 17. Model Number Structure Model Number Legend Note: Not all combinations are possible. Please refer to the list of models in Ordering Information on pages 2 and 3. S82J 1 1. Power Ratings 010: 10 W 025: 25 W 050: 50 W 100: 100 W 150: 150 W 300: 300 W 600: 600 W 2. [. . . ] Internal parts may occasionally deteriorate or be damaged if a short-circuited or other overcurrent state continues during operation. Eliminate the overcurrent state as soon as possible. In actual operation, the output voltage may not fall to 0 V when the overload protection function is triggered. Even with short-circuits on the load side, the drop in voltage will vary depending on factors such as the impedance in the load line. The overload protection function is activated at 105% of the rated output current for 300-W models. Inrush Current, Startup Time, Hold Time Input ON AC input voltage Input OFF 600-W Models Output voltage (V) Inrush current on input application AC input current 90% Output interrupted 0 50 100 Output current (%) 96. 5% Output voltage Startup time Hold time (20 ms min. ) 10 Switch Mode Power Supply S82J Dimensions Note: All units are in millimeters unless otherwise indicated. Open-frame type and covered type have the same dimensions. Front-mounting Bracket Type S82J-01090±1 Mounting Holes (Surface Screw Mounting) Side Mounting 8. 2 9. 5 Output indicator (Green) Output voltage adjuster +V DC output terminal -V Earthing terminal PE AC (L) Input terminal AC (N) +V -V AC AC 3. 5 Two, M3 97±1 65±0. 5 3. 5 dia. 65±0. 5 82±0. 5 Five, M3. 5 Nameplate 5 82±0. 5 5 Bottom Mounting 6. 5 3. 5 dia. 78±0. 5 Two, M3 17. 5 15 50±0. 5 3. 5 Two, M3 1 28 35± 78±0. 5 S82J-025124±1 3. 5 Mounting Holes (Surface Screw Mounting) Side Mounting Two, M3 +V 9. 5 8. 2 Output indicator (Green) Output voltage adjuster DC output terminal +V -V Earthing terminal PE AC (L) Input terminal AC (N) -V AC AC 97±1 65±0. 5 Five, M3. 5 Nameplate 65±0. 5 3. 5 dia. 116±0. 5 5 6. 5 3. 5 dia. Three, M3 17. 5 21. 5 83±0. 5 28 40±1 116±0. 5 112±0. 5 6 3. 5 Bottom Mounting Two, M3 112±0. 5 S82J-050161±1 3. 5 9. 5 8. 2 Output indicator (Green) Output voltage adjuster +V Mounting Holes (Surface Screw Mounting) Side Mounting Two, M3 97±1 65±0. 5 DC output terminal Five, M3. 5 Nameplate +V -V Earthing terminal PE AC (L) Input terminal AC (N) -V AC AC 65±0. 5 3. 5 dia. 153±0. 5 5 6. 5 3. 5 dia. Three, M3 10 22 127±0. 5 153±0. 5 150. 5±0. 5 7 20±0. 5 3. 5 Bottom Mounting Two, M3 28 40±1 20 150. 5±0. 5 Switch Mode Power Supply S82J 11 S82J-10024@ (100 W, 24-V Output) 9. 5 8. 2 12 max. 170±1 4. 5 Mounting Holes (Surface Screw Mounting) Side Mounting Two, M4 Output indicator (Green) Output voltage adjuster DC output terminal Earthing terminal +V -V PE AC (L) AC (N) +V 97±1 65±0. 5 4. 5 dia. -V AC AC 65±0. 5 Five, M3. 5 Nameplate Input terminal 162±0. 5 162±0. 5 160±0. 5 4. 5 7 5 6. 5 4. 5 dia. 27. 5 15 Three, M4 Bottom Mounting Two, M4 50±1 28±0. 5 25±0. 5 160±0. 5 100±0. 5 15 S82J-100@ (100 W, 5-/12-/15-V Output) S82J-15024@ (150 W) 198 (see note) 188 4 max. Mounting Holes (Surface Screw Mounting) Side Mounting Two, M4 4. 5 8. 1 9. 5 89±0. 5 97 82±0. 8 180±0. 5 7±0. 3 4. 5 dia. 180±0. 5 3±0. 25 M4 × 8 Bottom Mounting Two, M4 Mounting holes (on both sides) 4. 5 dia. 178±0. 5 3±0. 25 178±0. 5 4. 5 27. 5±0. 3 25±0. 5 50 35±0. 3 15 Three, M4 (6 max. deep) 100±0. 5 55±0. 3 S82J-30024@ (300 W) Nine, M4 terminal screws DC ON POWER SUPPLY V. ADJ INPUT 50/60Hz AC100-120V 8A AC200-230V 4A 4 (19) 181±1 Eight, M4 holes (depth: 8 max. on both sides) Mounting Holes (Surface Screw Mounting) Side Mounting 10 OUTPUT DC24V 14A +V L N Side OPERATION 8. 6 ALM 92±1 -V VOLTAGE SELECT SHORT 100-120V OPEN 200-230V 50±0. 5 Four, 4. 5 dia. 21 SHORT BAR OMRON Corporation MADE IN JAPAN PARALLEL SINGLE 50±0. 5 120±1 19 150±0. 5 Four, M4 holes (depth: 8 max. ) 10 150±0. 5 Bottom Mounting Four, 4. 5 dia. 100±0. 5 100±0. 5 19 150±0. 5 150±0. 5 12 Switch Mode Power Supply S82J S82J-60024@ (600 W) Eight, M4 holes (depth: 8 max. on both sides) Mounting Holes (Surface Screw Mounting) Side Mounting Four, 4. 5 dia. Four, M4 holes (depth: 8 max. on one side) Four, M4 holes (depth: 8 max. ) 150±0. 5 50±0. 5 Nine, M4 terminal screws Bottom Mounting Four, 4. 5 dia. 100±0. 5 150±0. 5 Dimensions with Mounting Brackets (Provided) For 10-/25-/50-/100 (24 V)-W Models Front-mounting Bracket (Provided) 1. 5 9 Two, 3. 5 dia. 11 4. 6 15±0. 2 Mounting Holes Using the Mounting Bracket Attach the mounting bracket to the panel and loosely tighten the two screws. Insert the projected parts of the bracket (b) to the square holes of the power supply (a). [. . . ] If that occurs and the Power Supplies are left in that state, internal circuits may be damaged. Although Power Supplies having different specifications can be connected in series, the current flowing through the load must not exceed the smaller rated output current. , if the load is shorted a reverse voltage may result in the Power Supply causing deterioration and damage. It is recommended that diodes are connected as shown in the previous diagram (D1, D2). [. . . ]