Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual OMRON TZ. We hope that this OMRON TZ user guide will be useful to you.
Lastmanuals help download the user guide OMRON TZ.
Detailed instructions for use are in the User's Guide.
[. . . ] 1 1 1 1 1 0. 4 Non-inductive load (A) Resistive load NO 0. 9 0. 45 0. 9 0. 9 0. 9 0. 05 NC 0. 45 0. 3 0. 45 0. 45 0. 45 0. 05 Lamp load NO 1 1 1 1 1 0. 4 NC Inductive load (A) Inductive load NO 1. 5 0. 45 1. 5 1. 5 1. 5 0. 05 NC 0. 75 0. 3 1. 5 1. 5 1. 5 0. 05 Motor load NO
The above current ratings are the values of the steady-state current. Inductive load has a power factor of 0. 4 min. Lamp load has an inrush current of 10 times the steady-state current. [. . . ] OP
0. 98 N {100 gf} 0. 14 N {14 gf} 3. 5 mm 4. 6 mm 1. 3 mm 18±1. 2 mm
Two, 3. 56-dia. holes Three, M3. 5 11. 4
Short Hinge Roller Lever
TZ-1GV22
26. 2R
(Stainless-steel lever) 9. 5 dia. OP
2. 35 N {240 gf} 0. 33 N {34 gf} 1. 5 mm 1. 9 mm 0. 6 mm 28. 6±1. 2 mm
Two, 3. 56-dia. holes Three, M3. 5
11. 4
High-temperature Basic Switch
TZ
F-147
Limit Switches
Note: 1. All units are in millimeters unless otherwise indicated. Each dimension has a tolerance of ±0. 4 mm unless otherwise specified.
Hinge Roller Lever
TZ-1GV2
48. 4R (Stainless-steel lever) 9. 5 dia. OP
1. 27 N {130 gf} 0. 2 N {20 gf} 2. 6 mm 3. 5 mm 1 mm 28. 6±1. 2 mm
Two, 3. 56-dia. holes 11. 4 Three, M3. 5
Precautions
Refer to the Technical Information for Basic Switches (Cat. C122) for common precautions.
Correct Use
Handling
The Switch has a ceramic casing. Do not drop the Switch from a height of 30 cm or more. Doing so will break the casing.
Operation
Do not modify the Actuator and change the operating position. Make sure that the switching speed is not extremely slow or do not use the Switch so that the pushbutton will be set to a position between the FP and OP. Make sure that the pin-type pushbutton and the switching stroke are on the same vertical line. Make sure that the switching frequency or speed is within the specified range. · If the switching speed is extremely slow, the contact may not be switched smoothly, which may result in a contact failure or contact welding. · If the switching speed is extremely fast, switching shock may damage the Switch soon. If the switching frequency is too high, the contact may not catch up with the speed. The rated permissible switching speed and frequency indicate the switching reliability of the Switch. [. . . ] Each terminal must be secured on the TZ with M3. 5 nut. Make sure that the ceramic case is free of metal powder or other impurities.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0. 03937. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE OMRON TZ
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual OMRON TZ will begin.
