User manual OMRON V400-R1CF

[. . . ] Z276-E1-01 Ultra small Multi-code Reader V400-R1CF/R1CS USER'S MANUAL Introduction Introduction Contents Contents Safety Precautions Regulations and Standards Precautions for Safe Use Precautions for Correct Use How to Use This Manual Visual Aids 1 5 6 7 9 11 13 Contents Section 1 Product Overview 15 16 18 19 Features Basic Configuration Part Names and Functions Section 2 Introduction Procedure 21 22 24 29 35 40 Introduction Flow Chart Preliminary Examination Wiring and Connection Preparation Installation and Reading Section 3 Basic Knowledge of Operation 43 44 50 Operation Flow Chart Communication Data Format Section 4 Setting Method 53 54 How to Use a Menu Sheet/Command V400-R1CF/R1CS User's Manual 1 Introduction Introduction Menu Sheet/Command List 56 Contents Section 5 Appendix 97 98 99 100 107 108 Maintenance Troubleshooting Specifications and External Dimension ASCII Code Table Quick-Reference Tables of Data Capacities 2 V400-R1CF/R1CS User's Manual Introduction Introduction READ AND UNDERSTAND THIS DOCUMENT Please read and understand this document before using the products. Please consult your OMRON representative if you have any questions or comments. WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. [. . . ] This is convenient when changing setup according to the type of code. Section 2 Preparation Read the menu sheet. The menu sheet is a special code used to set the reader function. Setting can be changed by reading this menu sheet. 1. Read the menu sheet "ZZ" that starts/ends the setting procedure. The buzzer sounds continuously, indicating that the reader has entered the setting mode. _ZZ_ 2. Read the menu sheet "U2" that restores the factory default settings. _U2_ 3. Read the menu sheet for the setting item you want to change. Menu Sheet/Command List p. 56 4. To finish, read the menu sheet "ZZ" that starts/ends the setting procedure. The buzzer stops and the reader returns to the normal mode. _ZZ_ V400-R1CF/R1CS User's Manual 37 Section 2 Introduction Procedure How to create a menu sheet Menu sheets use the CODE39 code system. However, the code used for this reader is special as a space mark is used as the start and stop codes. (Normally "*") You can create a menu sheet using readily available code creation software, as shown below. E. g. : When creating a menu sheet "A3" Create "* A3 *" and cut the parts of "*" with scissors to create the menu sheet "A3". Section 2 Preparation *_A3_* Cutting off section Cutting off section 38 V400-R1CF/R1CS User's Manual Section 2 Introduction Procedure Inputting a command from the upper equipment Upper equipment Multi-code reader V400-R1CF/R1CS OKIN G SCAN Transmits command character strings Section 2 Preparation 1. Transmit the command character strings of the function you want to set. Command Menu Sheet/Command List p. 56 2. Transmit the command "Z2" to write the setting data in the nonvolatile memory of the reader. Be sure to write the setting data in the nonvolatile memory whenever a condition is set by inputting a command from the upper equipment. When you turn the power OFF without writing the setting in the memory, the settings will be lost. Transmission method of the command by designating values and characters is explained as follows. E. g. : Setting "AB" on header (Designating codes directly) Header setting command Character "A" Character "B" V400-R1CF/R1CS User's Manual 39 Section 2 Introduction Procedure Installation and Reading This section explains how to install the reader and conduct a final check to confirm that the reader works successfully in the actual environment. Installation Section 2 Installation and Reading Installing the reader Install the reader at a distance where it captures the code correctly. Field of view and distance in relation to the code For information about the installation distance and code resolution, refer to "Reading range performance" on p. 26. Installing the mounting bracket To avoid regular reflection of illumination light, install the bracket at an angle of about 15 to 30 against the bar code. The mounting bracket supplied with the reader can be tilted between -30° and +30°. (Tightening torque: 0. 54 N·m) 1. Attach the mounting bracket to the reader (4-M3 screws × 4). 4-M3 screw Mounting bracket 40 V400-R1CF/R1CS User's Manual Section 2 Introduction Procedure 2. Install the mounting bracket to the installation location (2-M5 screw × 4) 30° Insulation board 2-M5 screw 2-M5 screw 30° Section 2 Installation and Reading · Do not apply stress to the cable when installing or using. · The reading distance and angle ranges may differ depending on labels. Before installing the reader, check that the label is read successfully. · Be sure to install the supplied insulation board to reduce the influence of inductive noise on the reader. Use the attached screws to install the insulation board. V400-R1CF/R1CS User's Manual 41 Section 2 Introduction Procedure MEMO Section 2 Installation and Reading 42 V400-R1CF/R1CS User's Manual Section 3 Basic Knowledge of Operation This section explains main functions of the reader. Section 3 Basic Knowledge of Operation Operation Flow Chart Communication Data Format 44 50 V400-R1CF/R1CS User's Manual 43 Section 3 Basic Knowledge of Operation Operation Flow Chart Basic operation flow charts by reading operation, data transmission charts by communication protocol, and timing charts of buzzer and LED indication are shown below. Basic operation flow chart In case of single reading Power on Section 3 Operation Flow Chart Wait for the reading trigger Illumination light on Repeat Reading process execution Has reading succeeded? Is the external trigger finished?(*1) Has reading effective duration passed?(*2) Illumination light off Illumination light off READ OK LED illuminates READ NG LED illuminates (*3) Reading data output Repeat Process when reading succeeded Process when reading failed Process when reading failed *1: When the trigger by a command is used, ignore this clause. [. . . ] Should be within a range of 35 to 85% when the interior temperature is measured. The reader and its mounting bracket must be properly secured. Tool required Voltmeter Thermometer Hygrometer Torque driver 98 V400-R1CF/R1CS User's Manual Section 5 Appendix Troubleshooting Connection Symptom Buzzer does not sound when power is supplied Cause · The power supply is not properly connected. · Not enough power capacity/current capacity. Refer to: p. 31 p. 100 Reading operation Symptom Unable to read Cause · Reading prohibition is set for the relevant code. [. . . ]