User manual OMRON V640

[. . . ] Z218-E1-01A AMPLIFIER UNIT V640-HAM12 CIDRW HEAD V640-HS62 CIDRW CONTROLLER V700-L22 LINK UNIT V700-L11 V640 SERIES USER'S MANUAL Introduction Thank you for purchasing the V640 Series CIDRW System. Please observe the following points when operating the V640 Series: · Please read and understand the content of this manual before using the system. · After reading this manual, store it in a handy location for easy reference whenever necessary. READ AND UNDERSTAND THIS DOCUMENT Please read and understand this document before using the products. Please consult your OMRON representative if you have any questions or comments. WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON. [. . . ] This can cause the system to stop operating correctly. Set Software Revisions The operations of the V700-L22 can be changed to match those of the previous model, the V700-L21. The commands, and the parameters that can be set are indicated below. List of Commands Designation Parameter designation Command input Explanation (Tag name) = (Set value) <CRLF> Specify the parameter value corresponding to the tag name. Checks the parameter designations that have been received so far and, if there is no error, confirms the settings. This is ignored as the comment line. Parameter confirmation ::END Comment # (Comment) <CRLF> or CRLF Tag Name List Parameter Software revision Tag name RVER Setting range 2. 00: in V700-L22 mode 1. 10: in V700-L21 mode 2. 00 Default setting 1. Specify the parameters to be changed. When the first parameter is specified, the ALARMS indicator flashes. RVER=1. 10 CIDRW System User's Manual 53 SECTION 3 Preparing for Communications 2. Confirm the parameter change. The input parameter is checked and written. ::END _ Check for Correct Setting 1. Send the parameter output command "::GET_VER" from the host device. The software revision settings are displayed. The currently set data can be output so that you can check if it is correct. ::GET_VER Set the Communications Conditions for the CIDRW Controller SECTION 3 RVER=1. 10 ::END _ Return to the Normal Operation mode When the Mode is Selected with the Mode Switch on the Bottom of the Unit 1. Turn OFF the power to the CIDRW Controller. Set the mode switch on the bottom of the unit to the 0. 7 5 67 1 23 3. When all of the devices to be used are connected, turn the power ON. Start up in the Normal Operation mode. Even if you restart with the mode switch left at the 3 position, or send a reset command "::EXIT, " the Controller will start in the Setting mode. To switch to Normal Operation mode, you must set the mode switch to 0. When the Mode is Selected by a Command Sent from the Host Device 1. Either send the reset command "::EXIT" from the host device or turn the power to the CIDRW Controller OFF and then back ON. Start up in the Normal Operation mode. ::EXIT _ 54 CIDRW System User's Manual 0 SECTION 3 Preparing for Communications Reference: List of Commands Designation Parameter designation Command input Explanation (Tag name) = (Set value) <CRLF> Specify the parameter value corresponding to the tag name. Checks the parameter designations that have been received so far and, if there is no error, confirms the settings. Outputs the set parameters (protocol, SECS, operation). Outputs the set parameters (ID Tag memory map). Outputs the set parameters (operations). Outputs the set parameters (software revision). Restarts the CIDRW Controller. Parameter confirmation ::END Comment Parameter output # (Comment) <CRLF> or CRLF ::GET_PARAM ::GET_SEG ::GET_E99SYS ::GET_VER RESET :EXIT SECTION 3 Set the Communications Conditions for the CIDRW Controller Tag Name List Classification Protocol Parameter Baud Rate Device ID Time-out between characters Protocol time-out Response time-out Time-out between blocks Retry limit Master/slave SECS Double block detection yes/no Tag name S_BAUD S_DEVID S_T1 S_T2 S_T3 S_T4 S_RTY S_MS S_DB Setting range 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 bps 0 to 32767 0. 1 to 10 s 0. 2 to 25 s 1 to 120 s 1 to 120 s 0 to 31 M: Master S: Slave 1: The header of the block currently being received is compared with the correct block received immediately before, and double blocks are detected. 0: Double block detection is not performed. 0 to 32767 0, 1 9600, 19200, 38400 bps Use a consistent baud rate setting within the same system configuration. [. . . ] The number of bytes in the carrier ID (if there are any non-visible ASCII characters in the carrier ID, the CIDRW returns an error to the host controller. Date on which the subsystem was installed CIDR / CIDRW classification Hardware revision number RW N CarrierIDlength RW N SECS Protocol Specifications SECTION 6 Option DateInstalled DeviceType HardwareRevisionLevel RW RO RO N N N 20 8 bytes All " " (space) on shipping 20 5 bytes "CIDRW" 20 6 bytes "VVV. RR" (VVV = version, RR = revision) 20 80 bytes All " " (space) on shipping 20 17 bytes "OMRON Corporation" 20 6 bytes "L22 " 20 max. 20 bytes (Not supported by the CIDRW) MaintenanceData Manufacturer ModelNumber SerialNumber Supplier dependent RW N N N N Manufacturer's name or ID RO Model name according to the maker System serial number RO RO 130 CIDRW System User's Manual SECTION 6 Appendix Reader/writer head attribute definition Attribute names Basic items HeadStatus Description Current status Access RO Request Y 20 "IDLE" "BUSY" "NOOP" HeadID Head number 1 to 31 RO Y 20 (multi) "01"-"31" ("00" indicates the CIDRW itself, so cannot be used. ) N 54 (unsigned 4-byte integer) (Not supported by the Reader/ Writer Head) 20 "NO": No alarm "NM": Status in which normal operation is not possible and maintenance is necessary "RW": Read/write error "RT": Read/write error rate (Not supported by the Reader/Writer Head) "NP": Status of power supply and connection errors HeadDateInstalled Date on which the head was installed Supplier dependent RO N 20 "YYYYMMDD" (Not supported by the Reader/ Writer Head) 20 (Not supported by the Reader/ Writer Head) Format and mounting Option Cycles Number of read/write oper- RO ations executed Maintenance status RO HeadCondition N SECTION 6 SECS Protocol Specifications HeadMaintenanceData N N CIDRW System User's Manual 131 SECTION 6 Appendix ASCII Code Table Leftmost bits b8 - b5 Rightmost bits Row b4 - b1 Line 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 0 1 2 3 4 5 6 7 5 9 10 11 12 13 14 15 NUL TC2(STX) TC3(ETX) TC4(EOT) TC6(ACK) BEL FE0(BS) FE1(HT) FE2(LF) FE3(VT) FE4(FF) FE5(CR) S0 S1 TC7(DLE) DC2 DC3 DC4 TC9(SYN) TC10(ETB) CAN EM SUB ESC IS4(FS) IS3(GS) IS2(RS) IS1(US) (SP) !@ A B C D E F G H I J K L M N O P Q R S T U V W X Y Z [ \ ] ^ _ ` a b c d e f g h i j k l m n o p q r s t u v w x y z { | } ÅP DEL Undefined Undefined Undefined TC1(SOH) DC1 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0000 1001 0010 0011 0100 0101 0110 0111 1000 1101 1010 1011 1100 1101 1110 1111 TC5(NEQ) TC8(NAK) ASCII Code Table SECTION 6 132 CIDRW System User's Manual SECTION 6 Appendix Protective Construction IPis governed by the test methods described below. [. . . ]