User manual OMRON V680-CA5D01-V2

[. . . ] No. Z249-E1-04 RFID System V680 Series ID Controller USER´S MANUAL RFID System V680 Series User's Manual ID Controller V680-CA5D01-V2 V680-CA5D02-V2 Cat. Z249-E1-04 Introduction Thank you for purchasing a V680-series RFID System. This manual describes the functions, performance, and application methods needed for optimum use of the V680-series RFID System. Please observe the following items when using the RFID System. [. . . ] n × × × 2 FCS × Terminator * 2 CR Controller No. @ 1 0 1 × Communications designation Specifies the method of communications with the Tag. Refer to Communications Designation Function for details on the communications designation. 103 Specifies the code format when sending the read data response. "A": ASCII "H": Hexadecimal Specifies the Antenna with which to communicate. "1": Antenna 1 "2": Antenna 2 A unique identifier used to identify Tags. Added only for the selective communications designation (SL). Specifies the start address of the area in the Tag from which data is to be read from in 4-digit hexadecimal. Setting range: 0000H to FFFAH Specifies the number of bytes to read from the Tag in 4-digit hexadecimal. Up to 510 bytes can be read with one command. Setting range: 0001H to FFFAH · ASCII: 510 bytes (510 characters) · Hexadecimal: 510 bytes (1, 020 characters) Data designation Antenna designation UID Read area start address SECTION 5 V680 Commands No. of bytes to read Response Communications Designation Other Than PA or PI Controller No. @ 1 0 1 × 2 × Antenna Resend flag desigCommand code End code nation Q 2 W 0 2 0 × 1 0 1 × × UID . . . 0 or 16 × × × 2 FCS × Terminator * 2 CR Note: When using the multi-access trigger communications designation (MT), the ID controller returns an end code of 03 after communicating with all Tags. Communications Designation of PA or PI Controller No. @ 1 0 1 × 2 × Command code Q 2 W Antenna Resend flag desigEnd code nation 0 2 1 × 1 0 1 × × UID . . . 0 or 16 × × × 2 FCS × Terminator * 2 CR UID A unique identifier used to identify Tags. In the case of multi-access communications designations (MT/MR), the UID of the Tag that is being written to is added to the data. RFID System User's Manual 139 SECTION 5 Communications Communications Subcommands Communications subcommands are used in combination with commands for Tag communications. They cannot be used by themselves to communicate with a Tag. POLLING QUERY (PC) 1:1 Protocol Command Query/cancel designation Command code P 2 C C/E 1 1/2 1 Antenna designation Terminator * 2 CR Query/cancel designation Specifies querying or canceling polling auto processing. "C": Processing results query "E": Processing cancelled. Specifies the Antenna with which to communicate. "1": Antenna 1 "2": Antenna 2 Antenna designation SECTION 5 V680 Commands Response When a Processing Results Query Is Executed after Tag Communications The ID Controller returns a response according to the specifications of the polling command that was executed. [. . . ] IP indicates the ingress protection symbol. IEC (International Electrotechnical Commission) Standards IEC 60529: 1989-11 (A) First Digit: Degree of Protection from Solid Materials Degree 0 50 mm dia. Degree No protection Protects against penetration of any solid object such as a hand that is 50 mm or more in diameter. 1 Protects against penetration of any solid object, such as a finger, that is 12. 5 mm or more in diameter. Protects against penetration of any solid object, such as a wire, that is 2. 5 mm or more in diameter. 12. 5 mm dia. 2 SECTION 7 Degree of Protection 0 1 2 2. 5 mm 3 Protects against penetration of any solid object, such as a wire, that is 1 mm or more in diameter. 4 1 mm 5 Protects against penetration of dust of a quantity that may cause malfunction or obstruct the safe operation of the product. Protects against penetration of all dust. 6 (B) Second Digit: Degree of Protection Against Water Degree No protection Protection against water drops Protection Not protected against water. [. . . ]