User manual OMRON Z300 V3 SETUP MANUAL

[. . . ] Note: Specifications subject to change without notice. This manual describes the hardware for the Z300 (High-precision Visual Displacement Measurement System) and how to install the components, and it includes the sections described below. This is one of two manuals used to operate the Z300. Refer to the following table for the contents of each manual. [. . . ] When a connector is not being used, leave the cap in place or replace the cap to protect against dust, dirt, and static electricity. Three ferrite cores (supplied with the sensor) must be attached to the sensor cable. Two ferrite cores can be connected within 100 mm from the sensor and within 100 mm from the controller's connector, respectively. However, their positions can be changed if necessary. When using an extension cable, make sure that two ferrite cores are connected within 100 mm from the sensor and within 100 mm from the controller's connector, respectively. However, their positions can be changed if necessary. Wire the power supply and the ground to their respective terminals. Cover the terminal blocks with the Terminal Block Protection Covers. -Always connect a ground wire to the Z300's ground terminal. To avoid grounding problems, do not share the ground wire with any other devices or wire the ground to the building's steel framing. -Use a grounding point that is as close as possible and keep the ground wiring as short as possible. Use a power supply that meets the following specifications. Use a DC power supply with countermeasures against high-voltage spikes (safe extra low-voltage circuits on the secondary side). In particular, keep the power supply wired separately from inductive loads. - Keep the power supply wiring as short as possible. ) - If UL recognition is required, use a UL class II power supply. Cover the terminal blocks with the Terminal Block Protection Covers. Use a DC power supply with countermeasures against high-voltage spikes (safe extra low-voltage circuits on the secondary side). Do not exceed the maximum load current specified for the Controller. ON Current/ON Voltage This refers to the current or voltage values needed to shift from the OFFON state. The ON voltage value is the potential difference between each of the input terminals and COM IN. OFF Current/OFF Voltage This refers to the current or voltage values needed to shift from the ONOFF state. [. . . ] Direct intra- Direct intraHigh power; Safe inherently protection norDescription of beam viewing beam viewing diffused reflecby engineering mally afforded hazard class with optical may be hazard- tion may be design by aversion aids may be ous hazardous responses hazardous Protective hous- Required for each laser product; limits access necessary for performance of ing functions of the products Safety interlock Designed to prevent removal of the panel until accessible emission values are in protective below the AEL for the class assigned housing Permits easy addition of exterRemote control Not required nal interlock in laser installation Laser inoperative when key is Key control Not required removed Give audible or visible warning when laser is switched on or if Emission warning Not required capacitor bank of pulsed laser device is being charged Give means beside On/Off Attenuator Not required switch to temporarily block beam Controls located so adjustment does not require Location controls Not required exposure to AEL above class 1 or 2 Viewing optics Emission from all viewing systems must be below Class 1 AEL's as applicable Scanning Scan failure shall not cause product to exceed its classification Required word- Warning and explanatory labels and specified wording (Refer to Class label ing page 12) Aperture label Not required Specified wording required Service entry Required as appropriate to the class of accessible radiation label Override interlock Required under certain conditions as appropriate to the class of laser used label User information Operation manuals must contain instructions for safe use Purchasing and Promotion brochures must reproduce classification labels; service manuals must service informacontain safety information tion Additional requirements for Cable service connections require tool to disconnect if disconnection breaks prolaser optical fibre tective housing and permits access above Class 1 transmission system Requirements; Sub-clause Class 1 Class 2 With respect to the requirements of remote interlock connector, key control, emission warning and attenuator, Class 3B laser products not exceeding five times the AEL of Class 2 in the wavelength range of 400 to 700 nm are to be treated as Class 3A laser products. Requirements I IIa Performance (all laser products) Protective R (see note 2) R (see note 2) R (see note 2) housing Safety interlock R R R (see notes 3, 4) (see notes 3, 4) (see notes 3, 4) Location of N/A R R controls Viewing optics R R R Scanning R R R safeguard Performance (laser systems) Remote control N/A N/A N/A connector Key control N/A N/A N/A Emission N/A N/A R indicator Beam attenuator N/A N/A R Reset N/A N/A N/A Performance (specific purpose products) Medical S S S Surveying, level- S S S ing, alignment Demonstration S S S Labeling (all laser products) Certification & R R R identification Protective D (see note 5) D (see note 5) D (see note 5) housing Aperture N/A N/A R Class warning N/A R (see note 6) R (see note 7) Information (all laser products) User information R R R Product literature N/A R R Service R R R information Class (see note 1) II IIIa IIIb Depends on level of interior radiation. Based on highest level accessible during operation. Required wherever & whenever human access to laser radiation above Class I limits is not needed for product to perform its function. [. . . ]