User manual OMRON ZEN-SOFT01-V4 12-2008

[. . . ] Z184-E1-04 ZEN-SOFT01-V4 ZEN Support Software OPERATION MANUAL ZEN-SOFT01-V4 ZEN Support Software Operation Manual Revised December 2008 Preface OMRON products are manufactured for use according to proper procedures by a qualified operator and only for the purposes described in this manual. This manual describes the functions, performance, and application methods needed for optimum use of the ZEN Programmable Relay. The ZEN is a compact and highly functional controller that can be used to easily automate small-scale applications. Its development has drawn on OMRON's advanced control technology and expertise in manufacturing various types of controllers. [. . . ] Then use any of the following methods to delete the rung. · Select Edit(E)/Delete Rung from the Menu Bar. · Right-click and select Rung(L)/Delete(R). Highlight the position and then select Edit(E)/Delete Rung from the Menu Bar. 1, 2, 3. . . 2. The highlighted rung will be deleted, and the next rung will be moved up. 2-5 Editing Comments The comment edit function is used to display or edit all I/O comments by bit type. 1, 2, 3. . . 1. Select Edit(E)/Edit Comments from the Menu Bar. 35 Saving Ladder Programs 2. Edit the comment in the Edit Comment Screen. Section 2-6 Note 1. Programs are easier to understand and manage if actual I/O device names or names relating to functions are used in the I/O comments. Click the Show Comments Button on the Toolbar or select View(V)/Show Symbol Comments from the Menu Bar to display or not display the I/O comments in ladder view on the screen. 2. 2-6 2-6-1 Saving Ladder Programs This section describes how to save ladder programs to file. Saving to File 1. Select File(F)/Save As(A) from the Menu Bar. The Save As Dialog Box will be displayed. Select the save destination and enter the file name, and then click the Save Button. 1, 2, 3. . . Note 1. When saving existing ladder programs that have been edited since they were saved, you can also click the Save Button on the 36 Printing Ladder Programs Section 2-7 Toolbar or select File(F)/Save(S) from the Menu Bar to overwrite the existing file. The system settings and password set under ZEN/Set Protection will also be saved with the file. 2-6-2 Opening Saved Files 1. Click the Open Button on the Toolbar or select File(F)/Open(O) from the Menu Bar to open saved files. The Open File Dialog Box will be displayed. Specify the file location and file name and click the Open Button. 1, 2, 3. . . 2-7 2-7-1 Printing Ladder Programs Print Settings This section describes the layout and heading settings that must be made before printing ladder programs. 1, 2, 3. . . 1. 2. Select File(F)/Print Setup(R) from the Menu Bar. The Print Settings Dialog Box will be displayed. Make the settings for each item. 37 Printing Ladder Programs Setting Program frame display Parameter settings information Explanation Section 2-7 Check this box to print the print frame. Check this box to print the timer, counter, and other parameter settings. Information will be printed only for portions of the memory areas that are being used. Enter the name of the person who wrote the program. Enter the date the program was written. Print title Drawing name Figure No. Revision mark Prepared by Date 3. Click the OK Button to save the settings as the print settings for the ZEN Support Software. Click the Cancel Button to discard the settings. [. . . ] 2. 0 Yes Yes Yes No (See note. ) No (See note. ) Ver. 3. 0 Yes Yes Yes Yes No (See note. ) Appendix B Ver. 4. 0 or 4. 1 Yes Yes Yes Yes Yes Note A message saying that it was not possible to read the file will be displayed if an attempt is made to read incompatible data. Compatibility between the ZEN CPU Unit and the Support Software Version of CPU Unit (See note 1. ) Ver. [. . . ]