User manual ONE FOR ALL 10-DEVICE UNIVERSAL REMOTE WITH LEARNING

[. . . ] OFA 10L with Learning Owners Manual. fm Page 0 Thursday, January 27, 2005 1:34 PM 10-Device Universal Remote with Learning Control Remoto Universal de 10 Dispositivos con Aprendizaje User's Guide Guía del Usuario OFA 10L with Learning Owners Manual. fm Page 1 Thursday, January 27, 2005 1:34 PM OWNER'S MANUAL TABLE OF CONTENTS Introduction . . 11 Programming a Macro on a Device Key . . 13 Deleting Functions from the Learning Keys . . 15 Restoring Keymoved Keys to Default Settings. [. . . ] After programming, point the remote control at the devices and press POWER for at least 2 seconds to sequentially turn on (or off) your devices. NOTE: When you press POWER for less than 2 seconds, a power command will only be sent to the currently-selected device. This allows you to still individually power devices on or off. Devices will turn on (or off) according to your programmed sequence. Press and hold SET until the LED (red light) blinks twice, then release SET. Press the AUD key (to select the receiver). Press digit 3 (for the input), and press DVD (to return control to the DVD key). To save the settings and exit the program, press and hold SET until the LED blinks twice, then release SET. NOTE: The currently-selected device will always turn on or off first, followed by the remaining programmed sequence. After the master power sequence has been completed, the remote control will be set to control the first powered-on device. NOTE: If one or more devices does not have a POWER key, the power off/on sequence may be slightly delayed when the remote control signals the device(s). This action is normal. NOTE: You can program up to 20 functions on the Device Key Macro. You can program a device Key Macro onto any device key. After programming, point the remote control at the receiver and press the DVD key for at least 2 seconds. This will switch the Receiver's input to input 3, to allow you to view the DVD. NOTE: When you press the device key (e. g. , DVD) for less than 2 seconds, the remote will only select the DVD mode but will not change the Input on the receiver. This allows you to still change modes while using the remote. NOTE: After executing the Device Key Macro, the remote will return to the DVD mode, to allow the control of the DVD device. PROGRAMMING A MACRO ON A DEVICE KEY In its default state, when you press a device key (e. g. , TV) on the One For All 10L Universal Remote Control with Learning (URC-10820 B00), the remote will switch to that selected device. However, you can also program a Macro onto the Device keys to allow for additional functionality. For example, if your devices are connected to a receiver unit, you can program a Device macro to switch the receiver's input to the selected device. To Program the Device Key Macro For example, let's assume that your DVD in connected to Input 3 of your receiver. You can program a macro that will switch the receiver's input to input 3 when you press and hold the DVD key. CLEARING A MACRO 1. Press and hold SET until the LED (red light) blinks twice, then release SET. Select a macro key (e. g. , M1, M2, M3 POWER or any device key) you want to clear and press it once. Using Macros 11 OFA 10L with Learning Owners Manual. fm Page 12 Thursday, January 27, 2005 1:34 PM ONE FOR ALL 10L UNIVERSAL REMOTE CONTROL WITH LEARNING 4. [. . . ] This equipment generates, uses, and can radiated radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. PROBLEM: 18 FCC Compliance OFA 10L with Learning Owners Manual. fm Page 19 Thursday, January 27, 2005 1:34 PM OWNER'S MANUAL However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · · · Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet or a circuit different from that to which the receiver is connected. [. . . ]