User manual ONE FOR ALL 8L UNIVERSAL

[. . . ] 8-Device Universal Remote with Learning Control Remoto Universal de 8 Dispositivos con Aprendizaje User's Guide Guía del Usuario OWNER'S MANUAL TABLE OF CONTENTS Introduction . . 10 Programming a Macro on a Device Key . . 13 Deleting Functions from the Learning Keys . . 14 Restoring Keymoved Keys to Default Settings. [. . . ] However, you can also program a Master Power Macro onto the POWER key that will sequentially NOTE: The currently-selected device will always turn on or off first, followed by the remaining programmed sequence. After the master power sequence has been completed, 10 Using Macros OWNER'S MANUAL the remote control will be set to control the first powered-on device. NOTE: If one or more devices does not have a POWER key, the power off/on sequence may be slightly delayed when the remote control signals the device(s). This action is normal. After programming, point the remote control at the receiver and press the DVD key for at least 2 seconds. This will switch the Receiver's input to input 3, to allow you to view the DVD. PROGRAMMING A MACRO ON A DEVICE KEY In its default state, when you press a device key (e. g. , TV) on the One For All 8L Universal Remote Control with Learning (URC-8820 B00), the remote will switch to that selected device. However, you can also program a Macro onto the Device keys to allow for additional functionality. For example, if your devices are connected to a receiver unit, you can program a Device macro to switch the receiver's input to the selected device. To Program the Device Key Macro For example, let's assume that your DVD in connected to Input 3 of your receiver. You can program a macro that will switch the receiver's input to input 3 when you press and hold the DVD key. Press and hold SET until the LED (red light) blinks twice, then release SET. Press the AUD key (to select the receiver) Press digit 3 (for the input), and press DVD (to return control to the DVD key). To save the settings and exit the program, press and hold SET until the LED blinks twice, then release SET. NOTE: When you press the device key (e. g. , DVD) for less than 2 seconds, the remote will only select the DVD mode but will not change the Input on the receiver. This allows you to still change modes while using the remote. NOTE: After executing the Device Key Macro, the remote will return to the DVD mode, to allow the control of the DVD device. CLEARING A MACRO 1. Press and hold SET until the LED (red light) blinks twice, then release SET. Select a macro key (e. g. , M1, M2, POWER or any device key) you want to clear and press it once. Press and hold SET until the LED blinks twice, then release SET. The macro is now deleted but the keys (in the case of POWER and device keys), will retain their original function. 4. USING CHANNEL SCAN In the TV, VCR, DVD and CBL/SAT modes, use the FAV key to start a 3-second scan of all favorite channels (if programmed, "Programming Favorite Channel Scan" on page 12) and/or all channels for the selected mode. · If Favorite Channel Scan has been set up, scanning of favorite channels will start and cycle through stored channels, then NOTE: You can program up to 20 functions on the Device Key Macro. You can program a device Key Macro onto any device key. To Operate the Device Key Macro Using Channel Scan 11 ONE FOR ALL 8L UNIVERSAL REMOTE CONTROL WITH LEARNING proceed to the next channel up and cycle through all channels on the selected device. · If Favorite Channel Scan has not been set up, scanning will start with the current channel, then proceed to the next channel up and cycle through all channels on the selected device. [. . . ] CH+ and CH- do not work for your RCA TV. SOLUTION: PROBLEM: SOLUTION: PROBLEM: PROBLEM: SOLUTION: SOLUTION: PROBLEM: PROBLEM: SOLUTION: SOLUTION: PROBLEM: SOLUTION: PROBLEM: Troubleshooting 17 ONE FOR ALL 8L UNIVERSAL REMOTE CONTROL WITH LEARNING SOLUTION: Due to RCA design (19831987), only the original remote control will operate these functions. See "Changing Volume Lock" on page 15 to lock/ unlock volume. Please contact us in any of the following ways: · Please visit: www. oneforall. com · If the above website is not able to provide you with the information you need, please email us at ofasupport@ueic. com and refer to "Troubleshooting" · Customer Support: (330) 405-8516 Mon- Fri from 9AM to 5PM ET · · However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. [. . . ]