User manual ONE FOR ALL BIG EASY 4

[. . . ] WALRB4P manual booklet 5/2/06 3:16 PM Page 2 TABLE OF CONTENTS Introduction . 10 Programming The Power Key For The Master Power Macro . 13 Locking Volume Control To One Mode (Global Volume Lock). 13 Unlocking Volume Control For A Single Device (Individual Volume Unlock) . [. . . ] Remove the old batteries and insert new ones within 10 minutes to ensure all of your programming information is restored. Device Type:______________ DVD Code: Device Type:______________ CBL/SAT Code: Device Type:______________ TV Code: Device Type:______________ 7 8 WALRB4P manual booklet 5/2/06 3:16 PM Page 9 SEARCHING FOR YOUR CODE If your device does not respond to the remote control after trying all codes listed for your brand, or if your brand is not listed at all, try searching for your code. NOTE: Before performing a code search for a DVD player or a VCR, turn on the device and insert the required media. 5. Repeat step 4 (on the previous page) three more times for remaining digits. For example, to find out which code is operating your TV: 1. Press and hold SET until the LED (red light) blinks twice, then release SET. 5. To save the settings and exit the program, press and hold SET until the LED blinks twice, then release SET. Operating The Master Power Macro 1. After programming, point the remote control at the devices and press POWER for at least 2 seconds to sequentially turn on (or off) your devices. NOTE: When POWER is pressed for less than 2 seconds, a power command will only be sent to the currently-selected device. This allows you to still individually power devices on or off. Devices will turn on (or off) according to your programmed sequence. NOTE: The currently-selected device will always turn on or off first, followed by the remaining programmed sequence. After the master power sequence has been completed, the remote control will be set to control the first powered-on device. NOTE: If one or more devices does not have a POWER key, the power off/on sequence may be slightly delayed when the remote control signals the device(s). This action is normal. continued on next page. . . 4. To view the code for the first digit, press 1 once. Wait 3 seconds, count the LED blinks (e. g. , three blinks = 3) and write down the number in the leftmost box in the TV code boxes on page 8. NOTE: If a code digit is "0", the LED will not blink. 9 10 WALRB4P manual booklet 5/2/06 3:16 PM Page 11 PROGRAMMING A MASTER POWER MACRO (continued) Clearing The Master Power Macro 1. Press and hold SET until the LED (red light) blinks twice, then release SET. Then press POWER once. 2. Press FAV once. · If Favorite Channel Scan has been set up, scanning of favorite channels will start with up to 100 channel changes or until stopped by pressing any key. · If Favorite Channel Scan has not been set up, scanning will start with the current channel, and continue up to 100 channel changes or until stopped by pressing any key. 3. To stop scanning channels at any time, press any key once. PROGRAMMING FAVORITE CHANNEL SCAN 3. Press and hold SET until the LED blinks twice, then release SET. In the CBL/SAT or TV mode, you can store a list of up to 10 favorite channels, in any order, that will be immediately scanned when FAV is pressed (see Using Channel Scan on the previous page). NOTE: Favorite channels can only be programmed for one mode. After programming, if FAV is pressed while in another mode, the remote control will start scanning all channels instead (if applicable to the selected device). RE-ASSIGNING DEVICE KEYS The One For All 4 Device Universal Remote Control can be set to control a second PVR, VCR, or DVD player. For example, to control a TV, a cable box, and two DVD players, re-assign the unused VCR/PVR key to operate the second DVD player as follows: 1. On the remote control, press and hold SET until the LED (red light) blinks twice, then release SET. The LED will blink twice. 1. On the remote control, press CBL/SAT or TV once. 2. 3. Press and hold SET until the LED (red light) blinks twice, then release SET. The VCR/PVR key is now ready to be set up to control your second DVD player. See Programming Device Control on page 8. 4. Use the keypad to enter a favorite channel number (e. g. , 031). Then press SET once. NOTE: If the original remote control required pressing an Enter key to change the channel, also press the ENTER key after the channel number (e. g. , 0 - 3 - 1 - ENTER). On some satellite receivers and cable boxes, you may need to press the SELECT (OK) key instead of ENTER. To re-assign a second VCR or PVR (or DVR) to the unused DVD key, repeat steps 1 through 4 . However, in step 3 substitute VCR/PVR for DVD, and in step 4 substitute DVD for VCR/PVR. [. . . ] Clear the device key as follows: Press and hold SET until the LED (red light) blinks twice, then release. Then press the device key to be cleared twice. Now repeat the Searching For Your Code method on page 9. CH + and CH - do not work for your RCA TV. [. . . ]