User manual ONE FOR ALL URC 9911

[. . . ] IR/RF LCD 8-DEVICE WITH LEARNING UNIVERSAL REMOTE CONTROL (URC-9910) User's Guide TABLE OF CONTENTS Introduction . 21 Setup Codes for Satellite Receivers . 23 Setup Codes for Audio Cassette Decks. 29 Deleting A Function From A Learning Key. [. . . ] · All products for sale and/or use outside the continental United States, Hawaii, Alaska, or Canada. 51 USING THE IR/RF COMMAND CENTER The One For All IR/RF LCD 8-Device With Learning Universal Remote Control (URC-9910) comes with an IR/RF Command Center which receives radio-frequency (RF) signals from the URC-9910 remote control, anywhere in your home, up to 100 feet away. Once it is set up, the IR/RF Command Center will convert the RF signals into Infrared (IR) signals to control your home theater devices. NOTE: The URC-9910 remote control transmits both an IR and an RF signal simultaneously. It is your option whether you want to install the IR/RF Command Center for extended remote control range. If you choose to do so, during testing do not aim the URC-9910 remote control at your home entertainment devices to verify that RF transmission is working. NOTE: The RF signal transmitted by the URC-9910 remote control, only works with the IR/RF Command Center. Setting Up The IR/RF Command Center 1. Find a location approximately 8 feet in front of your home theater devices. It should provide (line-ofsight) access to your equipment and a power outlet to plug in the IR/RF Command Center. Plug in the IR/RF Command Center's power cord and raise the telescoping antenna. Telescoping Antenna 2. IR Lens 3. 4. Position the IR/RF Command Center so the black IR Lens is aimed at your home theater devices. To test the IR/RF Command Center, take the URC-9910 remote control into another room in your home, up to100 feet away. Select a device key (e. g. , TV) and press it once. If it does not turn on, review the steps 1 through 3 and make any adjustments. If you continue to have a problem, perhaps there is an IR line-of sight problem. Try adding the enclosed IR Signal Extension Cord (see next page). Also review the tips in Optimizing IR/RF Command Center Reception on page 54. 52 Adding The IR Signal Extension Cord Included with the URC-9910 remote control package is an IR Signal Extension Cord for use with a home theater device that is not in direct line-of-sight of the IR/RF Command Center. If you are having problems remotely controlling a home theater device from another room, try performing the following installation: 1. Plug the 4-foot IR Signal Extension Cord into the back of the IR/RF Command Center. 2. 3. Run the IR Signal Extension Cord to the device that is not in line-of-sight of the IR/RF Command Center. Using the supplied double-sided tape, attach the IR Signal Extension Cord so that its LED is over or next to the IR sensor of your home theater device. LED 4. Test the installation by again taking the URC-9910 remote control into another room in your home, up to 100 feet* away. Select a device key (e. g. , TV) and press it once. The IR/RF Command Center will convert the RF signal from the URC-9910 remote control into an IR signal and transmit that signal through the IR Signal Extension Cord to turn on your device (e. g. , TV). If it does not turn on, try repositioning the LED until the device can be controlled, then re-attach the LED. *Distance may vary 53 USING THE RF/IR COMMAND CENTER (continued) Optimizing IR/RF Command Center Reception Here are some adjustment tips for optimizing the operation of your IR/RF Command Center: · Aim the URC-9910 remote control toward the room where the IR/RF Command Center is located. [. . . ] When this feature is activated, keys will remain backlit for 5 seconds after the last key press. In the setup mode, backlighting will remain on for 30 seconds. Use SET for all programming sequences. LIMITED WARRANTY One For All® warrants, to the original purchaser only, that this product will be free from defects in materials and workmanship, under normal use, for ninety (90) days from the date of original purchase. This limited warranty is valid only on ONE FOR ALL® product purchased and used in the United States of America or Canada, and does not apply to products used for industrial or commercial purpose. [. . . ]