User manual ONE FOR ALL URC 6131

[. . . ] IMPK6VR manual 1. 0 2/21/03 5:46 PM Page 1 6-DEVICE PVR Universal Remote Control User's Guide IMPK6VR manual 1. 0 2/21/03 5:46 PM Page 2 TABLE OF CONTENTS Introduction . 9 Programming DVD Player/VCR Combo Control. 12 Programming The Power Key For Master Power. 14 Restoring Keymoved Keys To Default Settings. [. . . ] Write down the code digits in the remaining TV code boxes on page 10. To check for codes of other devices, repeat steps 1 through 5, but substitute the appropriate device key for each device you are checking. Write down the device's code digits in the appropriate code boxes on page 10. 6. PROGRAMMING MASTER POWER In its default state, the POWER key on the URC-6131 remote control will individually power your home entertainment devices on or off. However, you can also program a Master Power function onto the POWER key that will sequentially turn on or off all the devices with a single key press. Programming The Power Key For Master Power 1. Press and hold SET until the LED (red light) blinks twice, then release SET. 12 IMPK6VR manual 1. 0 2/21/03 5:46 PM Page 13 2. Enter 9 - 9 - 5. Then press POWER once. 3. For the first device you want in the power on sequence, press its device key (e. g. , CBL/SAT) once. Repeat step 3 up to five more times to add desired devices to the power-on sequence. To save the settings and exit the program, press and hold SET until the LED blinks twice, then release SET. After programming, point the remote control at the devices and press POWER for at least 2 seconds to sequentially turn on or off your devices. NOTE: When POWER is pressed for less than 2 seconds, a power command will only be sent to the currently-selected device. This allows you to still individually power devices on or off. 4. 5. Operating Master Power 1. 2. You will see the devices turn on or off according to your programmed sequence. NOTE: The currently-selected device will always turn on first, followed by the remaining programmed sequence. After the master power sequence has been completed, the remote control will be set to control the first powered-on device. NOTE: If one or more devices does not have a POWER key, the power off/on sequence may be slightly delayed when the remote control signals the device(s). This action is normal. Clearing Master Power 1. Press and hold SET until the LED (red light) blinks twice, then release SET. Then press POWER once. 3. Press and hold SET until the LED blinks twice, then release SET. Master Power is now cleared. 13 IMPK6VR manual 1. 0 2/21/03 5:46 PM Page 14 USING KEYMOVER The One For All 6-Device PVR Universal Remote Control includes a Keymover feature that allows you to map (or copy) keys from one mode (i. e. , source mode) to another mode (i. e. , destination mode). NOTE: The following keys cannot be used as a source or destination: TV, PVR, DVD, CBL/SAT, AUD, VCR, and SET. Programming Keymover For example, if your VCR does not have volume control, you can map those keys (i. e. , VOL+, VOL-, and Mute) from the TV mode to the VCR mode as follows: 1. Press and hold SET until the LED (red light) blinks twice, then release SET. 8. For the source mode, press TV once. For the destination mode, press VCR once. For the destination key, press VOL+ once. The LED will blink twice indicating the keymoved sequence is correct. Repeat steps 1 through 7 twice more to map remaining volume control keys, substituting VOL- and Mute as source and destination keys in steps 4 and 6. Upon completion of the above procedure, you can now use your One For All 6-Device PVR Universal Remote Control to control the TV's volume and mute in the VCR mode, as well as in the TV mode. Restoring Keymoved Keys to Default Settings Restoring A Single Keymoved Key 1. [. . . ] · Consult the dealer or an experienced radio/TV technician for help 34 IMPK6VR manual 1. 0 2/21/03 5:46 PM Page 35 LIMITED WARRANTY One For All ("OFA") warrants, to the original purchaser only, that this product will be free from defects in materials and workmanship, under normal use, for ninety (90) days from the date of original purchase. This warranty does not cover damage or failures caused by products or services not supplied by OFA, or which result from accident, misuse, abuse, neglect, mishandling, misapplication, faulty installation, set-up adjustment, improper maintenance, alteration, maladjustment of consumer controls, modifications, commercial use, or that is attributable to acts of God. There are no express warranties except as listed above. OFA SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANT-ABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE. [. . . ]