User manual ONE FOR ALL URC-6520

[. . . ] When your device turns off, press and release MAGIC. Don't forget, press MAGIC as soon as your device turns off. The ZAPPER should now be ready to operate your device. Turn your device back on and try all the remote's functions to ensure they are working properly. [. . . ] A) Try all the codes listed for your brand. Try the search method. 6 7 Volume Programme + MAGIC Power Programme - = 4 TV SAT Programme+ Installing The Batteries Volume Volume + Important notes: - When you want to control your device, press the device key first (TV or SAT). - To search for the code for your Satellite Receiver or Cable Converter, follow the same instructions above, only press the SAT key during step 2. - During step 5, you may have to press these keys many times (up to 150!), so be patient. Remember, you must aim the ZAPPER at your device the entire time you are searching for your code. Programme + = 3 The ZAPPER needs 2 new "AAA/LRO3" alkaline batteries. Mute/Scan Programme - 1 2 Remove the battery cover from the back of the ZAPPER by pressing down on the tab. Code Blink Out After you have used the Search Method, you can find out which code the ZAPPER responded to by blinking back the code. It's handy to know your Television, Satellite Receiver or Cable Converter code for future reference. Remember, you can only blink back your code after the ZAPPER is operating your device. To blink out your TV code: You may be using the wrong code. Try Direct Set-Up again trying each code listed under your brand or start the search method over again to locate the proper code. Press TV, then press MAGIC until the light blinks twice. Then press: (Programme-) (Programme+) (Programme-) If your original remote did not have channel +/- keys, the Zapper may not operate this function. Volume - = 2 Volume + = 1 Match the batteries to the +/- marks inside the battery case, then insert the batteries. 3 Press the battery cover back into place. 1 2 3 4 5 6 7 8 TV Press the TV key on the ZAPPER. Then, press and hold the MAGIC key until the light blinks twice (the light will blink once then twice). Next, press Programme(-), Programme(-), Programme(+). For the first digit of your 5-digit code, press Volume + ( ) and count the red blinks. For the second digit, press Volume - ( count the red blinks. ) and Your TV switches to programme 1 when you press the power key before switching off OR you must press Power twice to switch on your TV?You cannot reach channel 10 and above on your TV or Satellite. Programme - = 4 ¯ 4210059 Arthur Martin 4210060 ASA 4210062 Asberg 4211095 Asora 4210070 Asuka 4210072 Atlantic 4210074 Atori 4210075 Auchan 4210080 Audiosonic 13314 12332 12331 11322 11132 14233 21233 11322 21114 11132 13314 11322 22413 21131 14232 12141 12224 12141 14232 11134 13242 14343 31224 12342 13443 12131 14211 23211 22233 12123 12224 12141 21131 14231 14232 14231 14143 22111 23211 12342 14232 22212 14233 23341 22413 21131 14143 14342 22242 14424 11321 11132 22423 14112 22224 14111 12132 14232 12224 13314 11132 22423 13314 31224 14114 11322 13444 22332 24432 11322 23313 22413 23322 22413 22423 Contents ABOUT YOUR ZAPPER Features and Functions INSTALLING THE BATTERIES SETTING UP THE ZAPPER Direct Set-Up Search Method ADVANCED OPERATION Controlling Colour & Brightness Scan TROUBLE-SHOOTING Helpful Hints Consumer Help-Line SET-UP CODES Quick Set-Up Codes Front Page Front Page Front Page Front Page Front Page Important notes: - In order to avoid having to reprogram your ZAPPER after you remove the batteries, you will need to insert new batteries within 5 minutes. - Also, it is best that you do not use rechargeable batteries. - On the inside of the battery compartment door you will find a label on which to write your set-up codes after your ZAPPER is set up for your shading devices. Please write down your codes for easy, future reference. (Example: To enter the Sony TV code 11133, you would press Volume+, Volume+, Volume+, Programme+, Programme+) If your device does not respond to the ZAPPER after you have tried all the codes listed for your brand, try the Search Method described on the reverse side. Make sure you write your correct 5 digit codes in the boxes provided inside the battery compartment and in the boxes provided on the reverse side. Setting Up The ZAPPER Direct Set-Up To set up the ZAPPER for your Television and Satellite Receiver (or Cable Converter) follow the instructions below. To set up your Television: For the third digit, press Programme(+) and count the red blinks. [. . . ] The illustration on the left and the chart below describe the features and functions of the ZAPPER universal remote control. 11132 11314 22332 14232 21213 14211 13444 11132 13314 31341 14232 14231 11322 13444 22414 12131 32122 21131 4211156 Awa 4211081 Ayomi 4211098 AYR 4210091 Baird 4210081 Audioton 4210084 Ausind 4210085 Autovox 21233 24124 22324 21233 11132 21131 11322 14334 11132 22413 22414 11322 14424 13314 11412 24324 32114 21323 14232 23211 22111 11132 31121 14233 22333 23241 11132 12121 21131 12121 11322 21321 11322 13314 21114 11141 4210093 Bang & Olufsen* 4210094 Barco 4210097 Basic Line 4210098 4210099 6 7 Now, aim the ZAPPER at your Television and press POWER. If your Television switches off, your ZAPPER should be ready to operate your device. Turn your device back on and try all the remote's functions to ensure they are working properly. If the functions do not work properly, repeat steps 1-6 using another code listed under your brand. Press then hold Brightness up = Press then hold Brightness down = Press then hold Important notes: - To set up your Satellite Receiver or Cable Converter, follow the same instructions above, only press the SAT key during step 3. [. . . ]