User manual ONE FOR ALL URC 8910

[. . . ] A/V LCD 8-DEVICE WITH LEARNING UNIVERSAL REMOTE CONTROL (URC-8910) User's Guide TABLE OF CONTENTS Introduction . 21 Setup Codes for Satellite Receivers . 23 Setup Codes for Audio Cassette Decks. 29 Deleting A Function From A Learning Key. [. . . ] Immediately, press COM SKIP once and then enter channel 26 (e. g. The cable converter will switch to channel 26 and, after 1 minute, automatically return to channel 2. The next time a commercial appears, try pressing COM SKIP once, followed by PREV once to activate the same sequence. For a more powerful Commercial Skip technique, try programming these steps into an open macro key (see Using Macros on page 34). This way you will be able to press one key to switch channels and return after a preset time. 49 RESTORING FACTORY DEFAULT SETTINGS The URC-8910 remote control includes an Operation Reset program that you can use to restore the unit to factory default settings. IMPORTANT: Executing this program will erase all custom settings, including Home Theater assignments, Macros, Learned Keys, Keymoved Keys, and all device assignments. 1. On the URC-8910 remote control, press and hold SET until you see the display change from the current device and time to [CODE SET]. NOTE: The device, its code, and time are examples. Your remote control settings may be different. NOTE: To exit programming at any time, press EXIT once or allow 30 seconds of inactivity to lapse. You will see [EXIT SETUP] as the remote control returns to normal operation. NOTE: [INVALID] means you have inadvertently pressed an incorrect key. Note your error and continue programming. 2. (x 2) Press the v key twice until you see the display change to [OPS RESET]. NOTE: If you go past [OPS RESET], press thew key one or more times to return to it. 3. SELECT Press SELECT once to begin programming. You will see the display change to [CLR SETUP]. 4. SELECT Press SELECT once to start the process. You will see the display change to [RESET RAM] as the active memory is cleared, followed by [RESET E2] as the preprogrammed memory is restored. Then you will see [EXIT SETUP] as the URC-8910 remote control automatically exits the programming mode and returns to normal operation. 50 ABOUT UPGRADING The URC-8910 remote control has the largest infrared code library available. However, if you purchase a brand new home entertainment or home automation device, it may not respond to the codes stored in the remote control's memory. If this happens, please contact our Customer Support department (see Troubleshooting Section on page 52) to upgrade the URC-8910 remote control. The Customer Support representative will search our entire database for a code that matches your device and instruct you how to enter it into your URC-8910 remote control. If the code for your home entertainment or home automation device is not in our database, we will need to "capture" the code for that device from its original remote control. A new code would then be created and entered into your URC-8910 remote control. If necessary, the Customer Support representative can instruct you how to begin the capture procedure. NOTE: One For All reserves the right to replace a returned remote control with a new one of equal or superior functionality. Upgrade Exclusions · Home entertainment or home automation devices controlled by radio frequency (RF/UHF), wired, or ultrasonic remote controls. Only devices controlled by infrared remote controls are covered. · Home entertainment or home automation devices not controlled by remote controls. · Products that operate over 100 kHz. · Infrared keyboards and infrared pointing devices (such as mouse substitutes). · All products for sale and/or use outside the continental United States, Hawaii, Alaska, or Canada. SPECIFICATIONS Remote Control Power . 4 AAA Batteries Remote Control Dimensions (H x W x D) . [. . . ] When this feature is activated, keys will remain backlit for 5 seconds after the last key press. In the setup mode, backlighting will remain on for 30 seconds. Use SET for all programming sequences. LIMITED WARRANTY One For All® warrants, to the original purchaser only, that this product will be free from defects in materials and workmanship, under normal use, for ninety (90) days from the date of original purchase. This limited warranty is valid only on ONE FOR ALL® product purchased and used in the United States of America or Canada, and does not apply to products used for industrial or commercial purpose. [. . . ]